All formats
| Name | Code | Layout | Size | Since | Spec |
|---|---|---|---|---|---|
| Link Layer 129 | |||||
| LE Uncoded PHY packet | A packet on the LE 1M or 2M PHY: preamble, access address, the PDU, a 24-bit CRC, and optionally a tone for direction finding. | 10-N octets | 4.0 | 2.1 | |
| LE Coded PHY packet | A packet on the LE Coded PHY: the uncoded preamble, then access address, coding indicator and PDU spread by S=2 or S=8 coding. | 5.0 | 2.2 | ||
| LE HDT PHY packet | A packet on the High Data Throughput PHY added in 7.0, with a control header and separate header and payload zones. | 7.0 | 2.7 | ||
| Advertising PDU in LE Uncoded PHY packet | A PDU on an advertising physical channel: a 16-bit header, then a payload whose layout the PDU Type selects. | 3-257 octets | 4.0 | 2.3 | |
|
ADV_ |
0b0000 |
Connectable and scannable undirected advertising: any device may scan or connect. | 6-37 octets | 4.0 | 2.3.1.1 |
|
ADV_ |
0b0001 |
Connectable directed advertising, addressed to one initiator. | 12 octets | 4.0 | 2.3.1.2 |
|
ADV_ |
0b0010 |
Non-connectable, non-scannable advertising: data for anyone listening, no reply possible. | 6-37 octets | 4.0 | 2.3.1.3 |
|
AUX_ |
0b0011 |
A scan request sent on a secondary advertising channel, for extended advertising. | 12 octets | 5.0 | 2.3.2.1 |
|
SCAN_ |
0b0011 |
A scanner asks an advertiser for its scan response data. | 12 octets | 4.0 | 2.3.2.1 |
|
SCAN_ |
0b0100 |
The advertiser's reply to a scan request, carrying additional advertising data. | 6-37 octets | 4.0 | 2.3.2.2 |
|
AUX_ |
0b0101 |
A connection request sent on a secondary advertising channel, answered with AUX_CONNECT_RSP. | 34 octets | 5.0 | 2.3.3.1 |
|
CONNECT_ |
0b0101 |
An initiator opens a connection: addresses, then the connection parameters in LLData. CONNECT_REQ until 4.2. | 34 octets | 4.0 | 2.3.3.1 |
|
ADV_ |
0b0110 |
Scannable undirected advertising: scanners may ask for more data, nobody can connect. | 6-37 octets | 4.0 | 2.3.1.4 |
|
ADV_ |
0b0111 |
Extended advertising on the primary channels: usually just points to an AUX_ADV_IND on a secondary channel. | 0-255 octets | 5.0 | 2.3.1.5 |
|
AUX_ |
0b0111 |
Extended advertising on a secondary channel, with the advertising data and the extended header. | 0-255 octets | 5.0 | 2.3.1.6 |
|
AUX_ |
0b0111 |
Continues the data of a previous extended advertising PDU when it does not fit into one. | 0-255 octets | 5.0 | 2.3.1.8 |
|
AUX_ |
0b0111 |
A scan response for extended advertising, sent on a secondary channel. | 0-255 octets | 5.0 | 2.3.2.3 |
|
AUX_ |
0b0111 |
Periodic advertising: sent at a fixed interval so scanners can synchronize to it. | 0-255 octets | 5.0 | 2.3.1.7 |
|
AUX_ |
0b0111 |
Periodic advertising with responses (5.4): the advertiser's PDU in a subevent. | 0-255 octets | 5.4 | 2.3.1.9 |
|
AUX_ |
0b0111 |
Periodic advertising with responses (5.4): a synchronized device's reply in a response slot. | 0-255 octets | 5.4 | 2.3.1.10 |
|
AUX_ |
0b1000 |
The advertiser confirms an AUX_CONNECT_REQ, so both know the connection exists. | 0-255 octets | 5.0 | 2.3.3.2 |
|
ADV_ |
0b1001 |
Decision-based advertising (6.0): carries decision data scanners filter on before asking for more. | 0-255 octets | 6.0 | 2.3.1.11 |
| Advertising PDU header in Advertising PDU | The advertising PDU header: PDU Type, address type bits, the channel selection bit (5.0 on) and the payload Length. | 2 octets | 4.0 | 2.3 | |
| Common Extended Advertising Payload in Advertising PDU | The common payload of extended advertising PDUs: an extended header of optional fields, then advertising data. | 1-318 octets | 5.0 | 2.3.4 | |
| Extended Header in Common Extended Advertising Payload | The extended header: a flags octet, then only the optional fields whose flag is set, in a fixed order. | 38-N octets | 5.0 | 2.3.4 | |
| AdvDataInfo (ADI) in Extended Header | Advertising data info: lets scanners spot duplicate or changed data and tell advertising sets apart. | 2 octets | 5.0 | 2.3.4.4 | |
| AuxPtr in Extended Header | Points to the next auxiliary PDU: its channel, PHY and when it starts. | 3 octets | 5.1 | 2.3.4.5 | |
| SyncInfo in Extended Header | What a scanner needs to follow a periodic advertising train: timing, channel map, access address and counter. | 18 octets | 5.0 | 2.3.4.6 | |
| LLData in CONNECT_IND | The connection parameters inside a connection request: access address, CRC seed, timing, channel map and hop. | 22 octets | 4.0 | 2.3.3.1 | |
| Data PDU in LE Uncoded PHY packet | A PDU on a data channel of a connection: header, payload, and a MIC once encryption is on. | 2-N octets | 4.0 | 2.4 | |
| Data PDU header in Data PDU | The data PDU header: payload kind, acknowledgment bits and Length; 5.1 adds the CTEInfo flag and field. | 2-3 octets | 4.0 | 2.4 | |
| CTEInfo in Data PDU header | Describes a Constant Tone Extension: its length in 8 µs units and whether it is for angle of arrival or departure. | 1 octet | 5.1 | 2.5.2 | |
| LL Control PDU in Data PDU | An LL Control PDU: an opcode, then the control data of that procedure. | 1-251 octets | 4.0 | 2.4.2 | |
|
LL_ |
0x00 |
The central changes the connection interval, latency or timeout, effective at an instant. | 12 octets | 4.0 | 2.4.2.1 |
|
LL_ |
0x01 |
The central changes which data channels the connection hops over, effective at an instant. | 8 octets | 4.0 | 2.4.2.2 |
|
LL_ |
0x02 |
Ends the connection, with a reason. | 2 octets | 4.0 | 2.4.2.3 |
|
LL_ |
0x03 |
The central starts encryption: key diversifier, its half of the session key diversifier and IV. | 23 octets | 4.0 | 2.4.2.4 |
|
LL_ |
0x04 |
The peripheral answers with its halves of the session key diversifier and IV. | 13 octets | 4.0 | 2.4.2.5 |
|
LL_ |
0x05 |
The peripheral signals it is ready to start encrypted traffic. | 1 octet | 4.0 | 2.4.2.6 |
|
LL_ |
0x06 |
Confirms the start of encryption; the first encrypted PDU in each direction. | 1 octet | 4.0 | 2.4.2.7 |
|
LL_ |
0x07 |
Says the opcode received was not understood, so the procedure is not supported. | 2 octets | 4.0 | 2.4.2.8 |
|
LL_ |
0x08 |
The central asks the peripheral which Link Layer features it supports, sending its own. | 9 octets | 4.0 | 2.4.2.9 |
|
LL_ |
0x09 |
Answers a feature request with the features both may use. | 9 octets | 4.0 | 2.4.2.10 |
|
LL_ |
0x0A |
The central pauses encryption to change the key. | 1 octet | 4.0 | 2.4.2.11 |
|
LL_ |
0x0B |
Confirms that encryption is paused. | 1 octet | 4.0 | 2.4.2.12 |
|
LL_ |
0x0C |
Tells the peer which Core version, company and implementation the Link Layer is. | 6 octets | 4.0 | 2.4.2.13 |
|
LL_ |
0x0D |
Rejects a request, with a reason. | 2 octets | 4.0 | 2.4.2.14 |
|
LL_ |
0x0E |
The peripheral asks the central for its features (4.1 on); LL_SLAVE_FEATURE_REQ before 5.3. | 9 octets | 4.1 | 2.4.2.15 |
|
LL_ |
0x0F |
Either side proposes new connection parameters, with preferred anchor offsets. | 24 octets | 4.1 | 2.4.2.16 |
|
LL_ |
0x10 |
The peripheral answers a parameter request with the values it accepts. | 1 octet | 4.1 | 2.4.2.17 |
|
LL_ |
0x11 |
Rejects a request and names which opcode it rejects. | 3 octets | 4.1 | 2.4.2.18 |
|
LL_ |
0x12 |
Asks for a reply, to check that the encrypted link still authenticates. | 1 octet | 4.1 | 2.4.2.19 |
|
LL_ |
0x13 |
Answers a ping. | 1 octet | 4.1 | 2.4.2.20 |
|
LL_ |
0x14 |
Announces the largest payloads and longest packets this side can send and receive (4.2 on). | 9-10 octets | 4.2 | 2.4.2.21 |
|
LL_ |
0x15 |
Answers a length request with this side's limits. | 9-10 octets | 4.2 | 2.4.2.21 |
|
LL_ |
0x16 |
Proposes which PHYs to use in each direction (5.0 on). | 3-4 octets | 5.0 | 2.4.2.22 |
|
LL_ |
0x17 |
The peripheral answers a PHY request with the PHYs it prefers. | 3-4 octets | 5.0 | 2.4.2.22 |
|
LL_ |
0x18 |
The central sets the PHYs for each direction, effective at an instant. | 5-10 octets | 5.0 | 2.4.2.23 |
|
LL_ |
0x19 |
The peripheral asks the central to keep at least a number of channels in the map. | 3 octets | 5.0 | 2.4.2.24 |
|
LL_ |
0x1A |
Asks the peer to send packets with a Constant Tone Extension, for direction finding. | 2 octets | 5.1 | 2.4.2.25 |
|
LL_ |
0x1B |
Answers a CTE request; this PDU itself carries the tone. | 1 octet | 5.1 | 2.4.2.26 |
|
LL_ |
0x1C |
Hands the timing of a periodic advertising train to the peer, so it can sync without scanning. | 35 octets | 5.1 | 2.4.2.27 |
|
LL_ |
0x1D |
Tells the peer this side's sleep clock accuracy and asks for its. | 2 octets | 5.1 | 2.4.2.28 |
|
LL_ |
0x1E |
Answers with this side's sleep clock accuracy. | 2 octets | 5.1 | 2.4.2.28 |
|
LL_ |
0x1F |
The central asks the peripheral to set up a connected isochronous stream, with its parameters. | 5 octets | 5.2 | 2.4.2.29 |
|
LL_ |
0x20 |
The peripheral accepts a CIS request and narrows the offset range. | 9 octets | 5.2 | 2.4.2.30 |
|
LL_ |
0x21 |
The central confirms the CIS: access address and timing. | 16-17 octets | 5.2 | 2.4.2.31 |
|
LL_ |
0x22 |
Ends a connected isochronous stream, with a reason. | 4 octets | 5.2 | 2.4.2.32 |
|
LL_ |
0x23 |
Asks the peer to change its transmit power on a PHY, and reports this side's. | 4 octets | 5.2 | 2.4.2.33 |
|
LL_ |
0x24 |
Answers a power control request with the new power and whether it hit a limit. | 5 octets | 5.2 | 2.4.2.34 |
|
LL_ |
0x25 |
Reports a change of this side's transmit power. | 5 octets | 5.2 | 2.4.2.35 |
|
LL_ |
0x26 |
The peripheral asks for connection subrating: using only every Nth connection event. | 11 octets | 6.0 | 2.4.2.36 |
|
LL_ |
0x27 |
The central sets the subrate factor and when it starts. | 11 octets | 6.0 | 2.4.2.37 |
|
LL_ |
0x28 |
The central asks the peripheral to report channel quality, and how often. | 4 octets | 5.3 | 2.4.2.38 |
|
LL_ |
0x29 |
The peripheral reports which channels it finds good, bad or unknown. | 11 octets | 5.3 | 2.4.2.39 |
|
LL_ |
0x2A |
Hands over a periodic advertising train with responses, with its response timing. | 9 octets | 5.4 | 2.4.2.40 |
|
LL_ |
0x2B |
Asks for one page of the extended feature set, now that features no longer fit 64 bits. | 27 octets | 6.0 | 2.4.2.41 |
|
LL_ |
0x2C |
Answers with one page of the extended feature set. | 27 octets | 6.0 | 2.4.2.41 |
|
LL_ |
0x2D |
Channel Sounding: the reflector sends its part of the security values. | 21 octets | 6.0 | 2.4.2.43 |
|
LL_ |
0x2E |
Channel Sounding: describes this side's distance measuring capabilities and asks for the peer's. | 10 octets | 6.0 | 2.4.2.44 |
|
LL_ |
0x2F |
Channel Sounding: answers with this side's capabilities. | 10 octets | 6.0 | 2.4.2.44 |
|
LL_ |
0x30 |
Channel Sounding: creates or removes a configuration (modes, channels, steps). | 16 octets | 6.0 | 2.4.2.45 |
|
LL_ |
0x31 |
Channel Sounding: accepts a configuration. | 2 octets | 6.0 | 2.4.2.46 |
|
LL_ |
0x32 |
Channel Sounding: proposes when and how often the measurement procedures run. | 29 octets | 6.0 | 2.4.2.47 |
|
LL_ |
0x33 |
Channel Sounding: answers a procedure request. | 22 octets | 6.0 | 2.4.2.48 |
|
LL_ |
0x34 |
Channel Sounding: fixes the procedure timing, effective at a connection event. | 19 octets | 6.0 | 2.4.2.49 |
|
LL_ |
0x35 |
Channel Sounding: asks to stop the procedures of a configuration. | 5 octets | 6.0 | 2.4.2.50 |
|
LL_ |
0x36 |
Channel Sounding: asks for the reflector's frequency actuation error table. | 1 octet | 6.0 | 2.4.2.51 |
|
LL_ |
0x37 |
Channel Sounding: sends the frequency actuation error per channel. | 73 octets | 6.0 | 2.4.2.52 |
|
LL_ |
0x38 |
Channel Sounding: changes the channels used for measurements, at an instant. | 13 octets | 6.0 | 2.4.2.53 |
|
LL_ |
0x39 |
Channel Sounding: the initiator sends its part of the values that seed the random sequences. | 21 octets | 6.0 | 2.4.2.42 |
|
LL_ |
0x3A |
Channel Sounding: confirms the stop. | 5 octets | 6.0 | 2.4.2.50 |
|
LL_ |
0x3B |
Proposes a range for the spacing between packets, for faster PHYs and longer packets. | 8 octets | 6.0 | 2.4.2.54 |
|
LL_ |
0x3C |
Sets the frame spacing both sides use. | 6 octets | 6.0 | 2.4.2.55 |
|
LL_ |
0x3D |
Carries an upper tester message over the air, for testing (6.2). | 2-251 octets | 6.2 | 2.4.2.56 |
|
LL_ |
0x3E |
Proposes a new interval and subrating together (6.2). | 13 octets | 6.2 | 2.4.2.57 |
|
LL_ |
0x3F |
Sets the new interval and subrating, effective at an instant (6.2). | 15 octets | 6.2 | 2.4.2.58 |
|
LL_ |
0x40 |
Starts encryption keyed by an elliptic curve exchange at the Link Layer (7.0). | 83 octets | 7.0 | 2.4.2.59 |
|
LL_ |
0x41 |
The peripheral's public key and random value for the Link Layer key exchange (7.0). | 83 octets | 7.0 | 2.4.2.60 |
|
LL_ |
0x42 |
Proposes payload window sizes for the High Data Throughput PHY (7.0). | 2 octets | 7.0 | 2.4.2.61 |
|
LL_ |
0x43 |
Answers with this side's payload window sizes for HDT (7.0). | 2 octets | 7.0 | 2.4.2.61 |
|
LL_ |
0x44 |
Turns link quality reporting for HDT on or off (7.0). | 2 octets | 7.0 | 2.4.2.62 |
|
LL_ |
0x45 |
Proposes a configuration for streams of a connected isochronous group (7.0). | 5 octets | 7.0 | 2.4.2.63 |
|
LL_ |
0x46 |
Accepts a CIG configuration (7.0). | 4 octets | 7.0 | 2.4.2.64 |
|
LL_ |
0x47 |
Removes a CIG configuration (7.0). | 4 octets | 7.0 | 2.4.2.65 |
|
LL_ |
0x48 |
The peripheral asks to change a CIS's configuration (7.0). | 8 octets | 7.0 | 2.4.2.66 |
|
LL_ |
0x49 |
The central changes the configuration of CISes in a group (7.0). | 4 octets | 7.0 | 2.4.2.67 |
|
LL_ |
0x4A |
Accepts a CIS update (7.0). | 3 octets | 7.0 | 2.4.2.68 |
| Isochronous PDU in LE Uncoded PHY packet | An isochronous PDU of a CIS or BIS: header, a fixed-time payload, and a MIC when encrypted. | 2-257 octets | 5.2 | 2.6 | |
| CIS PDU header in Isochronous PDU | The header of a connected isochronous PDU: acknowledgment bits, close and null flags, Length. | 2 octets | 5.2 | 2.6.1 | |
| BIS PDU header in Isochronous PDU | The header of a broadcast isochronous PDU: control subevent sequence bits and Length. | 2 octets | 5.2 | 2.6.2 | |
| BIG Control PDU in Isochronous PDU | A control PDU of a broadcast isochronous group: an opcode and its data. | 1-251 octets | 5.2 | 2.6.3 | |
|
BIG_ |
0x00 |
Changes the channels a BIG uses, at an instant. | 8 octets | 5.2 | 2.6.3.1 |
|
BIG_ |
0x01 |
Ends a BIG, with a reason, at an instant. | 4 octets | 5.2 | 2.6.3.2 |
| Public device address | A public device address: an IEEE-assigned company identifier and a company-assigned part. | 6 octets | 4.0–4.2 | 1.3.1 | |
| Random device address | A random device address, as 4.0 describes it: hash and random parts. | 6 octets | 4.0–4.0 | 1.3 | |
| Static device address | A static random address: random bits with the two top bits set, kept until power cycle at least. | 6 octets | 4.2 | 1.3.2.1 | |
| Non-resolvable private address | A non-resolvable private address: random bits with the two top bits clear, changed often. | 6 octets | 4.2 | 1.3.2.2 | |
| Resolvable private address | A resolvable private address: a random part and a hash of it under an IRK, so bonded peers can resolve it. | 6 octets | 4.2 | 1.3.2.2 | |
| AdvA field in Extended Header | The advertiser's address as an extended header field. | 6 octets | 5.0 | 2.3.4.1 | |
| TargetA field in Extended Header | The target device's address as an extended header field. | 6 octets | 5.0 | 2.3.4.2 | |
| TxPower field in Extended Header | The transmit power level, in dBm, as an extended header field. | 1 octet | 5.0 | 2.3.4.7 | |
| Decision data in ADV_DECISION_IND | Decision data (6.0): a resolvable tag scanners can check, then arbitrary data. | 0-N octets | 6.0 | 2.3.1.11 | |
| Resolvable Tag in Decision data | A resolvable tag: a hash and random value that a device with the key can verify. | 6 octets | 6.0 | 2.3.1.11 | |
| LE HDT PDU components in LE HDT PHY packet | How HDT PDUs are composed of a first and a second PDU (7.0). | 0-N octets | 7.0 | 2.7 | |
| LE HDT PDU Header Zone in LE HDT PDU components | The PDU header zone of an HDT packet (7.0). | 2-N octets | 7.0 | 2.7.2 | |
| LE HDT Rx Portion in LE HDT PDU Header Zone | The receive portion of an HDT packet (7.0). | 5-9 octets | 7.0 | 2.7.2.2 | |
| LE HDT Tx Portion in LE HDT PDU Header Zone | The transmit portion of an HDT packet (7.0). | 1-25 octets | 7.0 | 2.7.2.3 | |
| LE HDT LL Descriptor in LE HDT PDU Header Zone | An HDT Link Layer descriptor (7.0). | 5-6 octets | 7.0 | 2.7.2.3 | |
| ISOAL 1 | |||||
| Segmentation header in Isochronous PDU | The header ISOAL puts before each segment of a framed SDU: start or continuation, completion, length. | 2 octets | 5.2 | 2.2 | |
| Channel Sounding 1 | |||||
|
CS_ |
A Channel Sounding packet: preamble, access address and a sounding or random sequence for phase and time. | 5.5-N octets | 6.0 | 2 | |
| Test modes 13 | |||||
| Test command (transmitter, receiver) | A two-octet test command over the test UART: start a transmitter or receiver test on a channel. | 2 octets | 4.0 | 3.3.2 | |
| Test command (setup, end) | A two-octet test command to set up the test (length, PHY, modulation) or to end it. | 2 octets | 4.2 | 3.3.2 | |
| Test event | A two-octet event from the device under test: a status or a packet report. | 2 octets | 4.0 | 3.4 | |
|
LE_ |
Reports success or failure of the last command. | 2 octets | 4.0 | 3.4.1 | |
|
LE_ |
Reports how many test packets were received when a test ends. | 2 octets | 4.0 | 3.4.2 | |
| LE test packet (LE Uncoded PHYs) | A test packet on the LE uncoded PHYs: like an LE packet, with a payload of a known pattern. | 47-307 octets | 4.1 | 4.1 | |
| LE test packet (LE Coded PHY) | A test packet on the LE Coded PHY. | 5.0 | 4.1 | ||
| LE CS test packet | A Channel Sounding test packet. | 9.5-22.5 octets | 6.0 | 4.1 | |
| LE test packet PDU in LE test packet (LE Uncoded PHYs) | The test PDU: a header and the test payload. | 2-N octets | 4.1 | 4.1.4 | |
| LE test packet header in LE test packet PDU | The test PDU header: payload pattern type, CTE flag and payload length. | 2-3 octets | 4.1 | 4.1.4 | |
| LE HDT test packet (short format, format 0) | A short HDT test packet (7.0). | 7.0 | 4.2 | ||
| LE HDT test packet (format 1) | An HDT test packet, format 1 (7.0). | 7.0 | 4.2 | ||
| UTP message | An upper tester message: type, length and value (6.2 on). | 3-N octets | 6.2 | 5.2 | |
| Baseband 36 | |||||
| Basic Rate packet | A Basic Rate packet: access code, header, then the payload; shorter packets stop after the code or header. | 15.25-364.5 octets | 4.1 | 6.1.1 | |
| Enhanced Data Rate packet | An Enhanced Data Rate packet: access code and header at the basic rate, then a guard, a sync and the faster payload. | 4.0 | 6.1.2 | ||
|
BD_ |
The Bluetooth device address: lower address part, upper address part, non-significant part. | 6 octets | 4.1 | 1.2 | |
| Access code in Basic Rate packet | The access code that starts each packet: a preamble, a sync word derived from a LAP, and a trailer. | 8.5-9 octets | 4.0 | 6.3 | |
| Packet header in Basic Rate packet | The packet header: logical transport address, packet type, flow, ARQ and sequence bits, and an 8-bit HEC. | 18 bits | 4.1 | 6.4 | |
| Payload header (single-slot ACL) in Basic Rate packet | The one-octet payload header of single-slot ACL packets: logical link, flow, and a 5-bit length. | 1 octet | 4.1–5.3 | 6.6.2 | |
| Payload header (multi-slot and EDR ACL) in Basic Rate packet | The two-octet payload header of multi-slot and EDR ACL packets: logical link, flow, and a 10-bit length. | 2 octets | 4.0–5.3 | 6.6.2 | |
| NULL in Basic Rate packet | 0b0000 |
A packet with no payload, used to acknowledge or keep timing. | 4.0 | 6.5 | |
| POLL in Basic Rate packet | 0b0001 |
Like NULL, but the peripheral has to answer it. | 4.0 | 6.5 | |
| FHS in Basic Rate packet | 0b0010 |
Carries the frequency hop synchronization payload, during paging and role switches. | 20 octets | 4.0 | 6.5 |
| DM1 in Basic Rate packet | 0b0011 |
One slot of ACL data with 2/3 FEC; also carries LMP on every link. | 3-24 octets | 4.0 | 6.5 |
| 2-DH1 in Basic Rate packet | 0b0100 |
One slot of ACL data at 2 Mb/s (EDR). | 4-62 octets | 4.0 | 6.5 |
| DH1 in Basic Rate packet | 0b0100 |
One slot of ACL data without FEC. | 3-34 octets | 4.0 | 6.5 |
| HV1 in Basic Rate packet | 0b0101 |
SCO voice with 1/3 FEC, 10 octets, sent every second slot. | 10 octets | 4.0 | 6.5 |
| 2-EV3 in Basic Rate packet | 0b0110 |
eSCO data in one slot at 2 Mb/s. | 3-62 octets | 4.0 | 6.5 |
| HV2 in Basic Rate packet | 0b0110 |
SCO voice with 2/3 FEC, 20 octets, sent every fourth slot. | 20 octets | 4.0 | 6.5 |
| 3-EV3 in Basic Rate packet | 0b0111 |
eSCO data in one slot at 3 Mb/s. | 3-92 octets | 4.0 | 6.5 |
| EV3 in Basic Rate packet | 0b0111 |
eSCO data in one slot, with CRC and retransmission. | 3-32 octets | 4.0 | 6.5 |
| HV3 in Basic Rate packet | 0b0111 |
SCO voice without FEC, 30 octets, sent every sixth slot. | 30 octets | 4.0 | 6.5 |
| 3-DH1 in Basic Rate packet | 0b1000 |
One slot of ACL data at 3 Mb/s (EDR). | 4-91 octets | 4.0 | 6.5 |
| DV in Basic Rate packet | 0b1000 |
Voice and data in one SCO packet. | 13-22 octets | 4.0 | 6.5 |
| AUX1 in Basic Rate packet | 0b1001 |
One slot of ACL data without CRC and never retransmitted. | 1-30 octets | 4.0 | 6.5 |
| 2-DH3 in Basic Rate packet | 0b1010 |
Three slots of ACL data at 2 Mb/s (EDR). | 4-375 octets | 4.0 | 6.5 |
| DM3 in Basic Rate packet | 0b1010 |
Three slots of ACL data with 2/3 FEC. | 4-129 octets | 4.0 | 6.5 |
| 3-DH3 in Basic Rate packet | 0b1011 |
Three slots of ACL data at 3 Mb/s (EDR). | 4-560 octets | 4.0 | 6.5 |
| DH3 in Basic Rate packet | 0b1011 |
Three slots of ACL data without FEC. | 4-191 octets | 4.0 | 6.5 |
| 2-EV5 in Basic Rate packet | 0b1100 |
eSCO data in up to three slots at 2 Mb/s. | 3-362 octets | 4.0 | 6.5 |
| EV4 in Basic Rate packet | 0b1100 |
eSCO data in up to three slots with 2/3 FEC. | 3-122 octets | 4.0 | 6.5 |
| 3-EV5 in Basic Rate packet | 0b1101 |
eSCO data in up to three slots at 3 Mb/s. | 3-542 octets | 4.0 | 6.5 |
| EV5 in Basic Rate packet | 0b1101 |
eSCO data in up to three slots without FEC. | 3-182 octets | 4.0 | 6.5 |
| 2-DH5 in Basic Rate packet | 0b1110 |
Five slots of ACL data at 2 Mb/s (EDR). | 4-687 octets | 4.0 | 6.5 |
| DM5 in Basic Rate packet | 0b1110 |
Five slots of ACL data with 2/3 FEC. | 4-232 octets | 4.0 | 6.5 |
| 3-DH5 in Basic Rate packet | 0b1111 |
Five slots of ACL data at 3 Mb/s (EDR). | 4-1029 octets | 4.0 | 6.5 |
| DH5 in Basic Rate packet | 0b1111 |
Five slots of ACL data without FEC. | 4-347 octets | 4.0 | 6.5 |
| FHS payload in FHS | The FHS payload: the sender's address, class of device and clock, for paging and role switches. | 18 octets | 4.1 | 6.5.1.4 | |
| DV payload in DV | The DV packet's payload: a voice field and a data field in one packet. | 21.375-44.5 octets | 4.0 | 6.5.2.4 | |
| LMP 93 | |||||
|
LMP_ |
0x01 |
Asks for a fragment of the peer's device name. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x02 |
Carries a fragment of the device name and its total length. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x03 |
Accepts the PDU whose opcode it names. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x04 |
Rejects the PDU whose opcode it names, with a reason. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x05 |
Asks for the clock offset between the peripheral and the central. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x06 |
Answers with the clock offset. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x07 |
Closes the connection, with a reason. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x08 |
Sends the random number for an initialization key (legacy pairing). | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x09 |
Sends a random number for a combination key (legacy pairing). | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x0A |
Sends a unit key (legacy pairing, deprecated). | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x0B |
A challenge for authentication. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x0C |
The answer to an authentication challenge. | 5 octets | 4.0 | 5.1 |
|
LMP_ |
0x0D |
A random number for a temporary broadcast key. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x0E |
The temporary broadcast key, masked. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x0F |
Asks to switch encryption on or off. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x10 |
Proposes the encryption key size. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x11 |
Starts encryption, with the random number for the key. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x12 |
Stops encryption. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x13 |
Asks for a role switch at an instant. | 5 octets | 4.0 | 5.1 |
|
LMP_ |
0x14 |
Puts the link on hold, from an instant for a time. | 7 octets | 4.0 | 5.1 |
|
LMP_ |
0x15 |
Asks to put the link on hold. | 7 octets | 4.0 | 5.1 |
|
LMP_ |
0x17 |
Asks for sniff mode: the anchor offset, interval, attempt and timeout. | 10 octets | 4.0 | 5.1 |
|
LMP_ |
0x18 |
Asks to leave sniff mode. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x19 |
Asks to park the peripheral (park state was removed in 5.0). | 17 octets | 4.0–4.2 | 5.1 |
|
LMP_ |
0x1B |
Sets a broadcast scan window for parked peripherals. | 6 octets | 4.0–4.2 | 5.1 |
|
LMP_ |
0x1C |
Changes the beacon parameters of parked peripherals. | 13 octets | 4.0–4.2 | 5.1 |
|
LMP_ |
0x1D |
Unparks peripherals by their device address. | 17 octets | 4.0–4.2 | 5.1 |
|
LMP_ |
0x1E |
Unparks peripherals by their parked member address. | 15 octets | 4.0–4.2 | 5.1 |
|
LMP_ |
0x1F |
Asks the peer to raise its transmit power by one step. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x20 |
Asks the peer to lower its transmit power by one step. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x21 |
Says the transmit power is already at its maximum. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x22 |
Says the transmit power is already at its minimum. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x23 |
Lets the peer choose between packets with and without FEC by link quality. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x24 |
Says which data rate and packet size the sender prefers. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x25 |
Sends this side's LMP version, company and subversion, and asks for the peer's. | 6 octets | 4.0 | 5.1 |
|
LMP_ |
0x26 |
Answers with this side's version, company and subversion. | 6 octets | 4.0 | 5.1 |
|
LMP_ |
0x27 |
Sends this side's supported features (page 0) and asks for the peer's. | 9 octets | 4.0 | 5.1 |
|
LMP_ |
0x28 |
Answers with this side's features. | 9 octets | 4.0 | 5.1 |
|
LMP_ |
0x29 |
The central sets the poll interval and broadcast retransmissions. | 4 octets | 4.0 | 5.1 |
|
LMP_ |
0x2A |
Asks for a poll interval and broadcast retransmissions. | 4 octets | 4.0 | 5.1 |
|
LMP_ |
0x2B |
Sets up an SCO link: handle, timing, packet type, air mode. | 7 octets | 4.0 | 5.1 |
|
LMP_ |
0x2C |
Removes an SCO link, with a reason. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x2D |
Sets the most slots the peer may use per packet. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x2E |
Asks to allow packets of more slots. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x2F |
Asks for the peer's clock drift and jitter. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x30 |
Answers with clock drift and jitter. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x31 |
Says this side has finished setting up the link. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x32 |
Switches to the semi-permanent link key. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x33 |
Asks whether the peer's Host accepts the connection. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x34 |
Sends the slot offset between the two piconets before a role switch. | 9 octets | 4.0 | 5.1 |
|
LMP_ |
0x35 |
Suggests a paging scheme for future paging. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x36 |
Asks the peer to use a page scan scheme. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x37 |
Sets the link supervision timeout. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x38 |
Enters test mode. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x39 |
Configures a test: scenario, hopping, frequencies, power, packet type. | 10 octets | 4.0 | 5.1 |
|
LMP_ |
0x3A |
Asks which encryption key sizes the peer supports for broadcast. | 1 octet | 4.0 | 5.1 |
|
LMP_ |
0x3B |
Answers with a bit mask of supported key sizes. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x3C |
Switches adaptive frequency hopping on or off with a channel map, at an instant. | 16 octets | 4.0 | 5.1 |
|
LMP_ |
0x3D |
Announces an encapsulated payload, such as a public key, and its length. | 4 octets | 4.0 | 5.1 |
|
LMP_ |
0x3E |
Carries 16 octets of an encapsulated payload. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x3F |
A commitment in Secure Simple Pairing. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x40 |
A nonce in Secure Simple Pairing. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x41 |
Proves knowledge of the Diffie-Hellman key in Secure Simple Pairing. | 17 octets | 4.0 | 5.1 |
|
LMP_ |
0x42 |
Pauses AES encryption to refresh the key (4.1 on). | 17 octets | 4.1 | 5.1 |
|
LMP_ |
0x01 |
Accepts the extended PDU it names. | 4 octets | 4.0 | 5.1 |
|
LMP_ |
0x02 |
Rejects the extended PDU it names, with a reason. | 5 octets | 4.0 | 5.1 |
|
LMP_ |
0x03 |
Sends one page of extended features and asks for the peer's. | 12 octets | 4.0 | 5.1 |
|
LMP_ |
0x04 |
Answers with one page of extended features. | 12 octets | 4.0 | 5.1 |
|
LMP_ |
0x05 |
The central adjusts the piconet clock (4.1 on). | 15 octets | 4.1 | 5.1 |
|
LMP_ |
0x06 |
Acknowledges a clock adjustment. | 3 octets | 4.1 | 5.1 |
|
LMP_ |
0x07 |
The peripheral asks for a clock adjustment. | 6 octets | 4.1 | 5.1 |
|
LMP_ |
0x0B |
Switches between basic rate and EDR packet types. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x0C |
Sets up or changes an eSCO link: handle, timing, packet types and lengths, air mode. | 16 octets | 4.0 | 5.1 |
|
LMP_ |
0x0D |
Removes an eSCO link, with a reason. | 4 octets | 4.0 | 5.1 |
|
LMP_ |
0x10 |
Asks the peripheral to report channel classification for AFH. | 7 octets | 4.0 | 5.1 |
|
LMP_ |
0x11 |
Reports which channels the peripheral finds good or bad. | 12 octets | 4.0 | 5.1 |
|
LMP_ |
0x15 |
Proposes sniff subrating. | 9 octets | 4.0 | 5.1 |
|
LMP_ |
0x16 |
Answers a sniff subrating proposal. | 9 octets | 4.0 | 5.1 |
|
LMP_ |
0x17 |
Pauses encryption to change the key. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x18 |
Resumes encryption after a pause. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x19 |
Sends the IO capabilities and authentication requirements for Secure Simple Pairing. | 5 octets | 4.0 | 5.1 |
|
LMP_ |
0x1A |
Answers with this side's IO capabilities and requirements. | 5 octets | 4.0 | 5.1 |
|
LMP_ |
0x1B |
Says the numeric comparison failed. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x1C |
Says the passkey entry failed. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x1D |
Says the out-of-band pairing failed. | 2 octets | 4.0 | 5.1 |
|
LMP_ |
0x1E |
Reports keypresses during passkey entry. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x1F |
Asks the peer to change its transmit power, for EDR power control. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x20 |
Answers a power control request. | 3 octets | 4.0 | 5.1 |
|
LMP_ |
0x21 |
Asks for a reply, to check that the encrypted link still authenticates (4.1 on). | 2 octets | 4.1 | 5.1 |
|
LMP_ |
0x22 |
Answers a ping. | 2 octets | 4.1 | 5.1 |
|
LMP_ |
0x23 |
Slot availability masks: sets the type-0 submap (5.0 on). | 17 octets | 5.0 | 5.1 |
|
LMP_ |
0x24 |
Slot availability masks: defines a map of available slots. | 17 octets | 5.0 | 5.1 |
|
LMP_ |
0x25 |
Slot availability masks: switches to a defined map at an instant. | 9 octets | 5.0 | 5.1 |
| HCI 25 | |||||
| UART packet | An HCI packet on a UART (H4): one indicator octet that says which kind of HCI packet follows. | 1-N octets | 4.0 | 2 | |
| HCI Command packet in UART packet | 0x01 |
A command from the Host to the Controller: a 16-bit opcode, the length of the parameters, the parameters. | 3-N octets | 4.0 | 5.4.1 |
| HCI ACL Data packet in UART packet | 0x02 |
ACL data between Host and Controller: connection handle, flags, length, then a fragment of an L2CAP PDU. | 4-N octets | 4.0 | 5.4.2 |
| HCI Synchronous Data packet in UART packet | 0x03 |
SCO or eSCO data between Host and Controller: connection handle, status flags, length, the samples. | 3.25-N octets | 4.0 | 5.4.3 |
| HCI Event packet in UART packet | 0x04 |
An event from the Controller to the Host: an event code, the length of the parameters, the parameters. | 2-N octets | 4.0 | 5.4.4 |
| HCI ISO Data packet in UART packet | 0x05 |
Isochronous data between Host and Controller (5.2 on): handle, flags, length, an optional time stamp, an SDU fragment. | 12.125-N octets | 5.2 | 5.4.5 |
| HCI command opcode in HCI Command packet | The command opcode split into its two parts: the command within its group, and the group. | 2 octets | 4.0 | 5.4.1 | |
| Three-wire UART packet | A Three-wire UART packet: a 4-octet header, the payload, an optional CRC; SLIP framing around it. | 6-4101 octets | 4.0 | 4 | |
| Three-wire UART packet header in Three-wire UART packet | The Three-wire UART header: sequence and acknowledgment numbers, flags, packet type, length, checksum. | 4 octets | 4.0 | 4 | |
| Acknowledgment packets in Three-wire UART packet · formerly Acknowledgement Packets, Acknowledgment Packets | 0b0000 |
A packet that only acknowledges; it has no payload. | 0-4095 octets | 4.0 | 4.5 |
| HCI Command packet in Three-wire UART packet · formerly HCI Command Packet | 0b0001 |
An HCI command carried by the Three-wire UART. | 0-4095 octets | 4.0 | 4.5 |
| HCI ACL Data packet in Three-wire UART packet · formerly HCI ACL Data Packet | 0b0010 |
HCI ACL data carried by the Three-wire UART. | 0-4095 octets | 4.0 | 4.5 |
| HCI Synchronous Data packet in Three-wire UART packet · formerly HCI Synchronous Data Packet | 0b0011 |
HCI synchronous data carried by the Three-wire UART. | 0-4095 octets | 4.0 | 4.5 |
| HCI Event packet in Three-wire UART packet · formerly HCI Event Packet | 0b0100 |
An HCI event carried by the Three-wire UART. | 0-4095 octets | 4.0 | 4.5 |
| HCI ISO Data packet in Three-wire UART packet | 0b0101 |
HCI ISO data carried by the Three-wire UART (5.2 on). | 0-4095 octets | 5.2 | 4.5 |
| Vendor Specific in Three-wire UART packet | 0b1110 |
Vendor-specific payload. | 0-4095 octets | 4.0 | 4.5 |
| Link Control packet in Three-wire UART packet · formerly Link Control Packet | 0b1111 |
A link control message of the Three-wire UART itself: sync, configuration, sleep and wakeup. | 0-4095 octets | 4.0 | 4.5 |
| SYNC message in Link Control packet | Link establishment: sent until the peer answers, to find out it is there. | 2 octets | 4.0 | 8.4 | |
| SYNC RESPONSE message in Link Control packet | Answers a SYNC message. | 2 octets | 4.0 | 8.5 | |
| CONFIG message in Link Control packet | Link establishment: proposes the link's configuration (window size, CRC, flow control). | 3 octets | 4.0 | 8.6 | |
| CONFIG RESPONSE message in Link Control packet | Answers a CONFIG message with the configuration both will use. | 3 octets | 4.0 | 8.7 | |
| Configuration field in CONFIG message | The configuration octets of CONFIG and CONFIG RESPONSE: sliding window size and options. | 1 octet | 4.0 | 8.8 | |
| WAKEUP message in Link Control packet | Asks a sleeping peer to wake up. | 2 octets | 4.0 | 9.1 | |
| WOKEN message in Link Control packet | Says this side is awake. | 2 octets | 4.0 | 9.2 | |
| SLEEP message in Link Control packet | Says this side is going to sleep. | 2 octets | 4.0 | 9.3 | |
| L2CAP 49 | |||||
| B-frame | The basic L2CAP frame: a length, a channel identifier and the payload. | 4-65539 octets | 4.0 | 3.1 | |
| G-frame | A frame on the connectionless channel: basic header, then the PSM of the receiving service. | 6-N octets | 4.0 | 3.2 | |
| K-frame | A frame of an LE credit-based channel; the first of an SDU starts with the SDU's length. | 6-65541 octets | 4.1–5.0 | 3.4 | |
| C-frame | A control frame: the basic header on a signaling channel, then one or more commands. | 4-N octets | 4.0 | 4 | |
| Signaling command in C-frame | A signaling command: code, identifier, data length, then the command's data. | 4-N octets | 4.0 | 4 | |
|
L2CAP_ |
0x01 |
Answers a command that was not understood or not acceptable. | 6-N octets | 4.0 | 4.1 |
|
L2CAP_ |
0x02 |
Asks to open a channel to a service (BR/EDR). | 8-N octets | 4.0 | 4.2 |
|
L2CAP_ |
0x03 |
Answers a connection request: the new channel's endpoint, or why not (yet). | 12 octets | 4.0 | 4.3 |
|
L2CAP_ |
0x04 |
Proposes options for a channel, such as the MTU or retransmission mode (BR/EDR). | 12 octets | 4.0 | 4.4 |
|
L2CAP_ |
0x05 |
Answers a configuration request, accepting or countering its options. | 12 octets | 4.0 | 4.5 |
|
L2CAP_ |
0x06 |
Asks to close a channel. | 8 octets | 4.0 | 4.6 |
|
L2CAP_ |
0x07 |
Confirms that a channel is closed. | 8 octets | 4.0 | 4.7 |
|
L2CAP_ |
0x08 |
Asks for an echo, to test the link. | 4-N octets | 4.0 | 4.8 |
|
L2CAP_ |
0x09 |
Answers an echo request. | 4-N octets | 4.0 | 4.9 |
|
L2CAP_ |
0x0A |
Asks for information about the peer's L2CAP: MTU, extended features or fixed channels. | 6 octets | 4.0 | 4.10 |
|
L2CAP_ |
0x0B |
Answers an information request. | 8-N octets | 4.0 | 4.11 |
|
L2CAP_ |
0x0C |
Opens a channel on an AMP controller (removed after 5.2, with AMP). | 9-N octets | 4.0–5.2 | 4.14 |
|
L2CAP_ |
0x0D |
Answers a create channel request (AMP). | 12 octets | 4.0–5.2 | 4.15 |
|
L2CAP_ |
0x0E |
Asks to move a channel to another controller (AMP). | 7 octets | 4.0–5.2 | 4.16 |
|
L2CAP_ |
0x0F |
Answers a move channel request (AMP). | 8 octets | 4.0–5.2 | 4.17 |
|
L2CAP_ |
0x10 |
Confirms the outcome of a channel move (AMP). | 8 octets | 4.0–5.2 | 4.18 |
|
L2CAP_ |
0x11 |
Acknowledges a move confirmation (AMP). | 6 octets | 4.0–5.2 | 4.19 |
|
L2CAP_ |
0x12 |
The LE peripheral asks the central for new connection parameters. | 12 octets | 4.0 | 4.20 |
|
L2CAP_ |
0x13 |
The central accepts or rejects the requested connection parameters. | 6 octets | 4.0 | 4.21 |
|
L2CAP_ |
0x14 |
Asks to open an LE credit-based channel (4.1 on). | 14 octets | 4.1 | 4.22 |
|
L2CAP_ |
0x15 |
Answers an LE credit-based connection request. | 14 octets | 4.1 | 4.23 |
|
L2CAP_ |
0x16 |
Grants the peer more credits on a credit-based channel. | 8 octets | 4.1 | 4.24 |
|
L2CAP_ |
0x17 |
Asks to open up to five enhanced credit-based channels at once (5.2 on). | 16-24 octets | 5.2 | 4.25 |
|
L2CAP_ |
0x18 |
Answers an enhanced credit-based connection request, channel by channel. | 16-24 octets | 5.2 | 4.26 |
|
L2CAP_ |
0x19 |
Changes the MTU and MPS of enhanced credit-based channels. | 12-20 octets | 5.2 | 4.27 |
|
L2CAP_ |
0x1A |
Answers a reconfiguration request. | 6 octets | 5.2 | 4.28 |
| Configuration option in L2CAP_CONFIGURATION_REQ | A configuration option: type, length, then data; options follow each other in a configuration command. | 2-4 octets | 4.0 | 5 | |
| Maximum Transmission Unit (MTU) in Configuration option | 0x01 |
The largest SDU the sender can receive on the channel. | 4 octets | 4.0 | 5.1 |
| Flush Timeout option in Configuration option · formerly Flush Timeout Option | 0x02 |
How long the sender's controller keeps trying to deliver data before flushing it. | 4 octets | 4.0 | 5.2 |
| Quality of Service (QoS) option in Configuration option · formerly Quality of Service (QoS) Option | 0x03 |
Quality of service the sender asks for: service type, token rate, bandwidth, latency. | 24 octets | 4.0 | 5.3 |
| Retransmission and Flow Control option in Configuration option · formerly Retransmission and Flow Control Option | 0x04 |
Chooses basic, retransmission, flow control, enhanced retransmission or streaming mode, with timers and windows. | 11 octets | 4.0 | 5.4 |
| Frame Check Sequence (FCS) option in Configuration option · formerly Frame Check Sequence (FCS) Option | 0x05 |
Whether frames carry a frame check sequence. | 3 octets | 4.0 | 5.5 |
| Extended Flow Specification option in Configuration option · formerly Extended Flow Specification Option | 0x06 |
An extended flow specification, for guaranteed or best-effort traffic. | 18 octets | 4.0 | 5.6 |
| Extended Window Size option in Configuration option · formerly Extended Window Size Option | 0x07 |
A transmit window larger than the retransmission option allows. | 4 octets | 4.0 | 5.7 |
| Configuration Request flags in L2CAP_CONFIGURATION_REQ | The flags of a configuration request: whether more requests continue it. | 2 octets | 4.0–5.1 | 4.4 | |
| Configuration Response flags in L2CAP_CONFIGURATION_RSP | The flags of a configuration response: whether more responses continue it. | 2 octets | 4.0–5.1 | 4.5 | |
| I-frame in B-frame | An information frame of the retransmission, flow control and streaming modes: header, control field, data, check. | 6-65547 octets | 4.0 | 3.3 | |
| I-frame Enhanced Control Field in I-frame | The 16-bit control field of an I-frame in enhanced retransmission and streaming modes. | 2 octets | 4.0 | 3.3.2 | |
| I-frame Extended Control Field in I-frame | The 32-bit control field of an I-frame, with 14-bit sequence numbers for larger windows. | 4 octets | 4.0 | 3.3.2 | |
| I-frame Standard Control Field in I-frame | The 16-bit control field of an I-frame in retransmission and flow control modes. | 2 octets | 4.0 | 3.3.2 | |
| S-frame in B-frame | A supervisory frame: acknowledges I-frames or asks for retransmission; it carries no data. | 6-10 octets | 4.0 | 3.3 | |
| S-frame Enhanced Control Field in S-frame | The 16-bit control field of an S-frame in enhanced retransmission mode, with Poll and Final bits. | 2 octets | 4.0 | 3.3.2 | |
| S-frame Extended Control Field in S-frame | The 32-bit control field of an S-frame, with a 14-bit sequence number. | 4 octets | 4.0 | 3.3.2 | |
| S-frame Standard Control Field in S-frame | The 16-bit control field of an S-frame in retransmission and flow control modes. | 2 octets | 4.0 | 3.3.2 | |
| SDP 9 | |||||
| SDP PDU in B-frame | An SDP PDU: an ID, a transaction ID, the length of the parameters, the parameters. | 5-N octets | 4.0 | 4.2 | |
|
SDP_ |
0x01 |
Says a request was invalid, with an error code. | 7 octets | 4.0 | 4.4.1 |
|
SDP_ |
0x02 |
Asks for the handles of service records matching a pattern of UUIDs. | 4.0 | 4.5.1 | |
|
SDP_ |
0x03 |
Answers with service record handles. | 4.0 | 4.5.2 | |
|
SDP_ |
0x04 |
Asks for attributes of one service record. | 4.0 | 4.6.1 | |
|
SDP_ |
0x05 |
Answers with the attributes of the record. | 4.0 | 4.6.2 | |
|
SDP_ |
0x06 |
Searches by UUID pattern and reads attributes in one exchange. | 4.0 | 4.7.1 | |
|
SDP_ |
0x07 |
Answers with the attributes of every matching record. | 4.0 | 4.7.2 | |
| Data element | An SDP data element: a type and size descriptor, then the value; sequences nest elements. | 1-N octets | 4.0 | 3.4 | |
| ATT 32 | |||||
| Attribute PDU in B-frame | 0x0004 |
An Attribute Protocol PDU: an opcode, then the parameters of that PDU. | 1-N octets | 4.0 | 3.3.1 |
|
ATT_ |
0x01 |
Says a request failed: which request, at which handle, and why. | 5 octets | 4.0 | 3.4.1.1 |
|
ATT_ |
0x02 |
The client announces the largest ATT PDU it can receive. | 3 octets | 4.0 | 3.4.2.1 |
|
ATT_ |
0x03 |
The server announces the largest ATT PDU it can receive; both then use the smaller. | 3 octets | 4.0 | 3.4.2.2 |
|
ATT_ |
0x04 |
Asks for the handles and types of attributes in a range. | 5 octets | 4.0 | 3.4.3.1 |
|
ATT_ |
0x05 |
Lists handle and type pairs, all with 16-bit or all with 128-bit UUIDs. | 6-N octets | 4.0 | 3.4.3.2 |
|
ATT_ |
0x06 |
Finds attributes of a 16-bit type with a given value, such as services of one UUID. | 7-N octets | 4.0 | 3.4.3.3 |
|
ATT_ |
0x07 |
Lists the handle ranges of the attributes found. | 5-N octets | 4.0 | 3.4.3.4 |
|
ATT_ |
0x08 |
Reads the values of all attributes of a type in a range, such as characteristic declarations. | 7-21 octets | 4.0 | 3.4.4.1 |
|
ATT_ |
0x09 |
Lists handle and value pairs of the attributes read. | 4-N octets | 4.0 | 3.4.4.2 |
|
ATT_ |
0x0A |
Reads the value of one attribute. | 3 octets | 4.0 | 3.4.4.3 |
|
ATT_ |
0x0B |
Carries the value read, or as much of it as fits. | 1-N octets | 4.0 | 3.4.4.4 |
|
ATT_ |
0x0C |
Reads a long attribute value from an offset. | 5 octets | 4.0 | 3.4.4.5 |
|
ATT_ |
0x0D |
Carries the part of the value from the offset. | 1-N octets | 4.0 | 3.4.4.6 |
|
ATT_ |
0x0E |
Reads several attributes of known fixed length at once. | 5-N octets | 4.0 | 3.4.4.7 |
|
ATT_ |
0x0F |
Carries the values read, one after the other without lengths. | 1-N octets | 4.0 | 3.4.4.8 |
|
ATT_ |
0x10 |
Reads grouping attributes of a type in a range; used to discover primary services. | 7-21 octets | 4.0 | 3.4.4.9 |
|
ATT_ |
0x11 |
Lists each group's handle range and value. | 6-N octets | 4.0 | 3.4.4.10 |
|
ATT_ |
0x12 |
Writes an attribute value and asks for confirmation. | 3-N octets | 4.0 | 3.4.5.1 |
|
ATT_ |
0x13 |
Confirms a write. | 1 octet | 4.0 | 3.4.5.2 |
|
ATT_ |
0x16 |
Queues a part of a value for a long or reliable write. | 5-N octets | 4.0 | 3.4.6.1 |
|
ATT_ |
0x17 |
Echoes the queued part, so the client can check it. | 5-N octets | 4.0 | 3.4.6.2 |
|
ATT_ |
0x18 |
Writes or cancels all queued parts. | 2 octets | 4.0 | 3.4.6.3 |
|
ATT_ |
0x19 |
Confirms the queued writes were executed or cancelled. | 1 octet | 4.0 | 3.4.6.4 |
|
ATT_ |
0x1B |
The server sends an attribute value unasked, without acknowledgment. | 3-N octets | 4.0 | 3.4.7.1 |
|
ATT_ |
0x1D |
The server sends an attribute value unasked and waits for a confirmation. | 3-N octets | 4.0 | 3.4.7.2 |
|
ATT_ |
0x1E |
The client confirms an indication. | 1 octet | 4.0 | 3.4.7.3 |
|
ATT_ |
0x20 |
Reads several attributes of any length at once (5.2 on). | 5-N octets | 5.2 | 3.4.4.11 |
|
ATT_ |
0x21 |
Carries the values read, each with its length. | 5-N octets | 5.2 | 3.4.4.12 |
|
ATT_ |
0x23 |
Notifies several attribute values in one PDU, each with handle and length (5.2 on). | 9-N octets | 5.2 | 3.4.7.4 |
|
ATT_ |
0x52 |
Writes an attribute value without asking for a response. | 3-N octets | 4.0 | 3.4.5.3 |
|
ATT_ |
0xD2 |
Writes without response, signed with a key from pairing; removed in 6.3. | 15-N octets | 4.0–6.2 | 3.4.5.4 |
| GATT 8 | |||||
| Characteristic declaration value | The value of a characteristic declaration: properties, the handle of the value, and its UUID. | 5-19 octets | 4.0 | 3.3.1 | |
| Characteristic Properties in Characteristic declaration value | What a characteristic allows: broadcast, read, write with or without response, notify, indicate, signed write. | 1 octet | 4.0 | 3.3.1.1 | |
| Characteristic Extended Properties | More characteristic properties: reliable write and writable descriptors. | 2 octets | 4.0 | 3.3.3.1 | |
| Client Characteristic Configuration | Written by a client to switch notifications or indications of a characteristic on or off. | 2 octets | 4.0 | 3.3.3.3 | |
| Server Characteristic Configuration | Written by a client to switch the broadcasting of a characteristic on or off. | 2 octets | 4.0 | 3.3.3.4 | |
| Characteristic Presentation Format | Describes how to present a characteristic's value: data type, exponent, unit. | 7 octets | 4.0 | 3.3.3.5 | |
| Client Supported Features | The GATT features a client supports, such as robust caching and EATT. | 1 octet | 5.1 | 7.2 | |
| Server Supported Features | The GATT features a server supports, such as EATT. | 1 octet | 5.2 | 7.4 | |
| SMP 17 | |||||
| SMP command in B-frame | An SMP command on the Security Manager channel: a code, then that command's data. | 1-N octets | 4.0 | 3.3 | |
| Pairing Request in SMP command | 0x01 |
The initiator starts pairing, with its capabilities and the keys it wants exchanged. | 7 octets | 4.0 | 3.5.1 |
| Pairing Response in SMP command | 0x02 |
The responder answers with its capabilities; together they decide the pairing method. | 7 octets | 4.0 | 3.5.2 |
| Pairing Confirm in SMP command | 0x03 |
A commitment to a random value, checked once the value is revealed. | 17 octets | 4.0 | 3.5.3 |
| Pairing Random in SMP command | 0x04 |
Reveals the random value committed to in Pairing Confirm. | 17 octets | 4.0 | 3.5.4 |
| Pairing Failed in SMP command | 0x05 |
Ends pairing, with a reason. | 2 octets | 4.0 | 3.5.5 |
| Encryption Information in SMP command | 0x06 |
Hands over a long-term key (LE legacy pairing). | 17 octets | 4.0 | 3.6.2 |
| Central Identification in SMP command · formerly Master Identification | 0x07 |
Hands over EDIV and Rand, which identify the long-term key. Master Identification before 5.3. | 11 octets | 4.0 | 3.6.3 |
| Identity Information in SMP command | 0x08 |
Hands over the identity resolving key, to resolve private addresses later. | 17 octets | 4.0 | 3.6.4 |
| Identity Address Information in SMP command | 0x09 |
Hands over the device's public or static random identity address. | 8 octets | 4.0 | 3.6.5 |
| Signing Information in SMP command | 0x0A |
Hands over the key for signed writes; removed in 6.3. | 17 octets | 4.0–6.2 | 3.6.6 |
| Security Request in SMP command | 0x0B |
The peripheral asks the central to start pairing or encryption. | 2 octets | 4.0 | 3.6.7 |
| Pairing Public Key in SMP command | 0x0C |
Sends the device's P-256 public key (Secure Connections, 4.2 on). | 65 octets | 4.2 | 3.5.6 |
| Pairing DHKey Check in SMP command | 0x0D |
Proves both sides computed the same Diffie-Hellman key (Secure Connections). | 17 octets | 4.2 | 3.5.7 |
| Keypress Notification in SMP command | 0x0E |
Reports keypresses during passkey entry. | 2 octets | 4.2 | 3.5.8 |
| AuthReq in Pairing Request | The AuthReq octet: bonding flags, MITM, then Secure Connections, keypress and CT2 bits as versions add them. | 1 octet | 4.0 | 3.5.1 | |
| Key Distribution in Pairing Request | The key distribution octet: which keys follow pairing. | 1 octet | 4.0 | 3.6.1 | |
| GAP 3 | |||||
| AD structure in ADV_IND | One AD structure of advertising data: a length, a type, then the data; structures follow each other. | 1-N octets | 4.0 | 11 | |
| EIR data structure | One structure of BR/EDR extended inquiry response data: the same length, type and data as an AD structure. | 4.0 | 8 | ||
| Signed data | Data signed with a signing key: the data, a counter, and a MAC. | 24-N octets | 4.0–6.2 | 10.4.1 | |
| AMP 15 | |||||
| AMP command in B-frame | An AMP Manager command (removed after 5.2 with AMP): code, identifier, length, data. | 4-N octets | 4.0–5.2 | 3.1 | |
| AMP Command Reject in AMP command | 0x01 |
Rejects an AMP command that was not understood. | 6-N octets | 4.0–5.2 | 3.2 |
| AMP Discover Request in AMP command | 0x02 |
Asks which AMP controllers the peer has. | 8 octets | 4.0–5.2 | 3.3 |
| AMP Discover Response in AMP command | 0x03 |
Lists the peer's AMP controllers. | 11-N octets | 4.0–5.2 | 3.4 |
| AMP Change Notify in AMP command | 0x04 |
Reports a change of the controller list. | 7-N octets | 4.0–5.2 | 3.5 |
| AMP Change Response in AMP command | 0x05 |
Acknowledges a change notification. | 4 octets | 4.0–5.2 | 3.6 |
| AMP Get Info Request in AMP command | 0x06 |
Asks for information about one AMP controller. | 5 octets | 4.0–5.2 | 3.7 |
| AMP Get Info Response in AMP command | 0x07 |
Answers with the controller's bandwidth, latency and capabilities. | 22 octets | 4.0–5.2 | 3.8 |
| AMP Get AMP Assoc Request in AMP command | 0x08 |
Asks for the AMP association data of a controller. | 5 octets | 4.0–5.2 | 3.9 |
| AMP Get AMP Assoc Response in AMP command | 0x09 |
Answers with the AMP association data. | 8 octets | 4.0–5.2 | 3.10 |
| AMP Create Physical Link Request in AMP command | 0x0A |
Asks to create a physical link on an AMP. | 8 octets | 4.0–5.2 | 3.11 |
| AMP Create Physical Link Response in AMP command | 0x0B |
Answers a create physical link request. | 7 octets | 4.0–5.2 | 3.12 |
| AMP Disconnect Physical Link Request in AMP command | 0x0C |
Asks to disconnect a physical link on an AMP. | 6 octets | 4.0–5.2 | 3.13 |
| AMP Disconnect Physical Link Response in AMP command | 0x0D |
Answers a disconnect request. | 7 octets | 4.0–5.2 | 3.14 |
| Controller list in AMP Discover Response | The list of AMP controllers: each entry an ID, a type and a status. | 15 octets | 4.0–5.2 | 3.4 | |
Changes
Pick two versions to see which formats and fields were added, removed, renamed or resized.
Decode
Paste bytes and auto-decode them. Based on the version picked above.