BlueTools

Bluetooth Packets and PDUs

Core 4.0 to 7.0 431 PDUs and formats from the Core Spec

All formats

Packet and PDU formats, Core 4.0 to 7.0
Name Code Layout Size Since Spec
Link Layer 129
LE Uncoded PHY packet A packet on the LE 1M or 2M PHY: preamble, access address, the PDU, a 24-bit CRC, and optionally a tone for direction finding. 10-N octets 4.0 2.1
LE Coded PHY packet A packet on the LE Coded PHY: the uncoded preamble, then access address, coding indicator and PDU spread by S=2 or S=8 coding. 5.0 2.2
LE HDT PHY packet A packet on the High Data Throughput PHY added in 7.0, with a control header and separate header and payload zones. 7.0 2.7
Advertising PDU in LE Uncoded PHY packet A PDU on an advertising physical channel: a 16-bit header, then a payload whose layout the PDU Type selects. 3-257 octets 4.0 2.3
ADV_IND in Advertising PDU 0b0000 Connectable and scannable undirected advertising: any device may scan or connect. 6-37 octets 4.0 2.3.1.1
ADV_DIRECT_IND in Advertising PDU 0b0001 Connectable directed advertising, addressed to one initiator. 12 octets 4.0 2.3.1.2
ADV_NONCONN_IND in Advertising PDU 0b0010 Non-connectable, non-scannable advertising: data for anyone listening, no reply possible. 6-37 octets 4.0 2.3.1.3
AUX_SCAN_REQ in Advertising PDU 0b0011 A scan request sent on a secondary advertising channel, for extended advertising. 12 octets 5.0 2.3.2.1
SCAN_REQ in Advertising PDU 0b0011 A scanner asks an advertiser for its scan response data. 12 octets 4.0 2.3.2.1
SCAN_RSP in Advertising PDU 0b0100 The advertiser's reply to a scan request, carrying additional advertising data. 6-37 octets 4.0 2.3.2.2
AUX_CONNECT_REQ in Advertising PDU 0b0101 A connection request sent on a secondary advertising channel, answered with AUX_CONNECT_RSP. 34 octets 5.0 2.3.3.1
CONNECT_IND in Advertising PDU · formerly CONNECT_REQ 0b0101 An initiator opens a connection: addresses, then the connection parameters in LLData. CONNECT_REQ until 4.2. 34 octets 4.0 2.3.3.1
ADV_SCAN_IND in Advertising PDU 0b0110 Scannable undirected advertising: scanners may ask for more data, nobody can connect. 6-37 octets 4.0 2.3.1.4
ADV_EXT_IND in Advertising PDU 0b0111 Extended advertising on the primary channels: usually just points to an AUX_ADV_IND on a secondary channel. 0-255 octets 5.0 2.3.1.5
AUX_ADV_IND in Advertising PDU 0b0111 Extended advertising on a secondary channel, with the advertising data and the extended header. 0-255 octets 5.0 2.3.1.6
AUX_CHAIN_IND in Advertising PDU 0b0111 Continues the data of a previous extended advertising PDU when it does not fit into one. 0-255 octets 5.0 2.3.1.8
AUX_SCAN_RSP in Advertising PDU 0b0111 A scan response for extended advertising, sent on a secondary channel. 0-255 octets 5.0 2.3.2.3
AUX_SYNC_IND in Advertising PDU 0b0111 Periodic advertising: sent at a fixed interval so scanners can synchronize to it. 0-255 octets 5.0 2.3.1.7
AUX_SYNC_SUBEVENT_IND in Advertising PDU 0b0111 Periodic advertising with responses (5.4): the advertiser's PDU in a subevent. 0-255 octets 5.4 2.3.1.9
AUX_SYNC_SUBEVENT_RSP in Advertising PDU 0b0111 Periodic advertising with responses (5.4): a synchronized device's reply in a response slot. 0-255 octets 5.4 2.3.1.10
AUX_CONNECT_RSP in Advertising PDU 0b1000 The advertiser confirms an AUX_CONNECT_REQ, so both know the connection exists. 0-255 octets 5.0 2.3.3.2
ADV_DECISION_IND in Advertising PDU 0b1001 Decision-based advertising (6.0): carries decision data scanners filter on before asking for more. 0-255 octets 6.0 2.3.1.11
Advertising PDU header in Advertising PDU The advertising PDU header: PDU Type, address type bits, the channel selection bit (5.0 on) and the payload Length. 2 octets 4.0 2.3
Common Extended Advertising Payload in Advertising PDU The common payload of extended advertising PDUs: an extended header of optional fields, then advertising data. 1-318 octets 5.0 2.3.4
Extended Header in Common Extended Advertising Payload The extended header: a flags octet, then only the optional fields whose flag is set, in a fixed order. 38-N octets 5.0 2.3.4
AdvDataInfo (ADI) in Extended Header Advertising data info: lets scanners spot duplicate or changed data and tell advertising sets apart. 2 octets 5.0 2.3.4.4
AuxPtr in Extended Header Points to the next auxiliary PDU: its channel, PHY and when it starts. 3 octets 5.1 2.3.4.5
SyncInfo in Extended Header What a scanner needs to follow a periodic advertising train: timing, channel map, access address and counter. 18 octets 5.0 2.3.4.6
LLData in CONNECT_IND The connection parameters inside a connection request: access address, CRC seed, timing, channel map and hop. 22 octets 4.0 2.3.3.1
Data PDU in LE Uncoded PHY packet A PDU on a data channel of a connection: header, payload, and a MIC once encryption is on. 2-N octets 4.0 2.4
Data PDU header in Data PDU The data PDU header: payload kind, acknowledgment bits and Length; 5.1 adds the CTEInfo flag and field. 2-3 octets 4.0 2.4
CTEInfo in Data PDU header Describes a Constant Tone Extension: its length in 8 µs units and whether it is for angle of arrival or departure. 1 octet 5.1 2.5.2
LL Control PDU in Data PDU An LL Control PDU: an opcode, then the control data of that procedure. 1-251 octets 4.0 2.4.2
LL_CONNECTION_UPDATE_IND in LL Control PDU · formerly LL_CONNECTION_UPDATE_REQ 0x00 The central changes the connection interval, latency or timeout, effective at an instant. 12 octets 4.0 2.4.2.1
LL_CHANNEL_MAP_IND in LL Control PDU · formerly LL_CHANNEL_MAP_REQ 0x01 The central changes which data channels the connection hops over, effective at an instant. 8 octets 4.0 2.4.2.2
LL_TERMINATE_IND in LL Control PDU 0x02 Ends the connection, with a reason. 2 octets 4.0 2.4.2.3
LL_ENC_REQ in LL Control PDU 0x03 The central starts encryption: key diversifier, its half of the session key diversifier and IV. 23 octets 4.0 2.4.2.4
LL_ENC_RSP in LL Control PDU 0x04 The peripheral answers with its halves of the session key diversifier and IV. 13 octets 4.0 2.4.2.5
LL_START_ENC_REQ in LL Control PDU 0x05 The peripheral signals it is ready to start encrypted traffic. 1 octet 4.0 2.4.2.6
LL_START_ENC_RSP in LL Control PDU 0x06 Confirms the start of encryption; the first encrypted PDU in each direction. 1 octet 4.0 2.4.2.7
LL_UNKNOWN_RSP in LL Control PDU 0x07 Says the opcode received was not understood, so the procedure is not supported. 2 octets 4.0 2.4.2.8
LL_FEATURE_REQ in LL Control PDU 0x08 The central asks the peripheral which Link Layer features it supports, sending its own. 9 octets 4.0 2.4.2.9
LL_FEATURE_RSP in LL Control PDU 0x09 Answers a feature request with the features both may use. 9 octets 4.0 2.4.2.10
LL_PAUSE_ENC_REQ in LL Control PDU 0x0A The central pauses encryption to change the key. 1 octet 4.0 2.4.2.11
LL_PAUSE_ENC_RSP in LL Control PDU 0x0B Confirms that encryption is paused. 1 octet 4.0 2.4.2.12
LL_VERSION_IND in LL Control PDU 0x0C Tells the peer which Core version, company and implementation the Link Layer is. 6 octets 4.0 2.4.2.13
LL_REJECT_IND in LL Control PDU 0x0D Rejects a request, with a reason. 2 octets 4.0 2.4.2.14
LL_PERIPHERAL_FEATURE_REQ in LL Control PDU · formerly LL_SLAVE_FEATURE_REQ 0x0E The peripheral asks the central for its features (4.1 on); LL_SLAVE_FEATURE_REQ before 5.3. 9 octets 4.1 2.4.2.15
LL_CONNECTION_PARAM_REQ in LL Control PDU 0x0F Either side proposes new connection parameters, with preferred anchor offsets. 24 octets 4.1 2.4.2.16
LL_CONNECTION_PARAM_RSP in LL Control PDU 0x10 The peripheral answers a parameter request with the values it accepts. 1 octet 4.1 2.4.2.17
LL_REJECT_EXT_IND in LL Control PDU · formerly LL_REJECT_IND_EXT 0x11 Rejects a request and names which opcode it rejects. 3 octets 4.1 2.4.2.18
LL_PING_REQ in LL Control PDU 0x12 Asks for a reply, to check that the encrypted link still authenticates. 1 octet 4.1 2.4.2.19
LL_PING_RSP in LL Control PDU 0x13 Answers a ping. 1 octet 4.1 2.4.2.20
LL_LENGTH_REQ in LL Control PDU 0x14 Announces the largest payloads and longest packets this side can send and receive (4.2 on). 9-10 octets 4.2 2.4.2.21
LL_LENGTH_RSP in LL Control PDU 0x15 Answers a length request with this side's limits. 9-10 octets 4.2 2.4.2.21
LL_PHY_REQ in LL Control PDU 0x16 Proposes which PHYs to use in each direction (5.0 on). 3-4 octets 5.0 2.4.2.22
LL_PHY_RSP in LL Control PDU 0x17 The peripheral answers a PHY request with the PHYs it prefers. 3-4 octets 5.0 2.4.2.22
LL_PHY_UPDATE_IND in LL Control PDU 0x18 The central sets the PHYs for each direction, effective at an instant. 5-10 octets 5.0 2.4.2.23
LL_MIN_USED_CHANNELS_IND in LL Control PDU 0x19 The peripheral asks the central to keep at least a number of channels in the map. 3 octets 5.0 2.4.2.24
LL_CTE_REQ in LL Control PDU 0x1A Asks the peer to send packets with a Constant Tone Extension, for direction finding. 2 octets 5.1 2.4.2.25
LL_CTE_RSP in LL Control PDU 0x1B Answers a CTE request; this PDU itself carries the tone. 1 octet 5.1 2.4.2.26
LL_PERIODIC_SYNC_IND in LL Control PDU 0x1C Hands the timing of a periodic advertising train to the peer, so it can sync without scanning. 35 octets 5.1 2.4.2.27
LL_CLOCK_ACCURACY_REQ in LL Control PDU 0x1D Tells the peer this side's sleep clock accuracy and asks for its. 2 octets 5.1 2.4.2.28
LL_CLOCK_ACCURACY_RSP in LL Control PDU 0x1E Answers with this side's sleep clock accuracy. 2 octets 5.1 2.4.2.28
LL_CIS_REQ in LL Control PDU 0x1F The central asks the peripheral to set up a connected isochronous stream, with its parameters. 5 octets 5.2 2.4.2.29
LL_CIS_RSP in LL Control PDU 0x20 The peripheral accepts a CIS request and narrows the offset range. 9 octets 5.2 2.4.2.30
LL_CIS_IND in LL Control PDU 0x21 The central confirms the CIS: access address and timing. 16-17 octets 5.2 2.4.2.31
LL_CIS_TERMINATE_IND in LL Control PDU 0x22 Ends a connected isochronous stream, with a reason. 4 octets 5.2 2.4.2.32
LL_POWER_CONTROL_REQ in LL Control PDU 0x23 Asks the peer to change its transmit power on a PHY, and reports this side's. 4 octets 5.2 2.4.2.33
LL_POWER_CONTROL_RSP in LL Control PDU 0x24 Answers a power control request with the new power and whether it hit a limit. 5 octets 5.2 2.4.2.34
LL_POWER_CHANGE_IND in LL Control PDU 0x25 Reports a change of this side's transmit power. 5 octets 5.2 2.4.2.35
LL_SUBRATE_REQ in LL Control PDU 0x26 The peripheral asks for connection subrating: using only every Nth connection event. 11 octets 6.0 2.4.2.36
LL_SUBRATE_IND in LL Control PDU 0x27 The central sets the subrate factor and when it starts. 11 octets 6.0 2.4.2.37
LL_CHANNEL_REPORTING_IND in LL Control PDU 0x28 The central asks the peripheral to report channel quality, and how often. 4 octets 5.3 2.4.2.38
LL_CHANNEL_STATUS_IND in LL Control PDU 0x29 The peripheral reports which channels it finds good, bad or unknown. 11 octets 5.3 2.4.2.39
LL_PERIODIC_SYNC_WR_IND in LL Control PDU 0x2A Hands over a periodic advertising train with responses, with its response timing. 9 octets 5.4 2.4.2.40
LL_FEATURE_EXT_REQ in LL Control PDU 0x2B Asks for one page of the extended feature set, now that features no longer fit 64 bits. 27 octets 6.0 2.4.2.41
LL_FEATURE_EXT_RSP in LL Control PDU 0x2C Answers with one page of the extended feature set. 27 octets 6.0 2.4.2.41
LL_CS_SEC_RSP in LL Control PDU 0x2D Channel Sounding: the reflector sends its part of the security values. 21 octets 6.0 2.4.2.43
LL_CS_CAPABILITIES_REQ in LL Control PDU 0x2E Channel Sounding: describes this side's distance measuring capabilities and asks for the peer's. 10 octets 6.0 2.4.2.44
LL_CS_CAPABILITIES_RSP in LL Control PDU 0x2F Channel Sounding: answers with this side's capabilities. 10 octets 6.0 2.4.2.44
LL_CS_CONFIG_REQ in LL Control PDU 0x30 Channel Sounding: creates or removes a configuration (modes, channels, steps). 16 octets 6.0 2.4.2.45
LL_CS_CONFIG_RSP in LL Control PDU 0x31 Channel Sounding: accepts a configuration. 2 octets 6.0 2.4.2.46
LL_CS_REQ in LL Control PDU 0x32 Channel Sounding: proposes when and how often the measurement procedures run. 29 octets 6.0 2.4.2.47
LL_CS_RSP in LL Control PDU 0x33 Channel Sounding: answers a procedure request. 22 octets 6.0 2.4.2.48
LL_CS_IND in LL Control PDU 0x34 Channel Sounding: fixes the procedure timing, effective at a connection event. 19 octets 6.0 2.4.2.49
LL_CS_TERMINATE_REQ in LL Control PDU 0x35 Channel Sounding: asks to stop the procedures of a configuration. 5 octets 6.0 2.4.2.50
LL_CS_FAE_REQ in LL Control PDU 0x36 Channel Sounding: asks for the reflector's frequency actuation error table. 1 octet 6.0 2.4.2.51
LL_CS_FAE_RSP in LL Control PDU 0x37 Channel Sounding: sends the frequency actuation error per channel. 73 octets 6.0 2.4.2.52
LL_CS_CHANNEL_MAP_IND in LL Control PDU 0x38 Channel Sounding: changes the channels used for measurements, at an instant. 13 octets 6.0 2.4.2.53
LL_CS_SEC_REQ in LL Control PDU 0x39 Channel Sounding: the initiator sends its part of the values that seed the random sequences. 21 octets 6.0 2.4.2.42
LL_CS_TERMINATE_RSP in LL Control PDU 0x3A Channel Sounding: confirms the stop. 5 octets 6.0 2.4.2.50
LL_FRAME_SPACE_REQ in LL Control PDU 0x3B Proposes a range for the spacing between packets, for faster PHYs and longer packets. 8 octets 6.0 2.4.2.54
LL_FRAME_SPACE_RSP in LL Control PDU 0x3C Sets the frame spacing both sides use. 6 octets 6.0 2.4.2.55
LL_OTA_UTP_IND in LL Control PDU 0x3D Carries an upper tester message over the air, for testing (6.2). 2-251 octets 6.2 2.4.2.56
LL_CONNECTION_RATE_REQ in LL Control PDU 0x3E Proposes a new interval and subrating together (6.2). 13 octets 6.2 2.4.2.57
LL_CONNECTION_RATE_IND in LL Control PDU 0x3F Sets the new interval and subrating, effective at an instant (6.2). 15 octets 6.2 2.4.2.58
LL_ENC_ECDH_REQ in LL Control PDU 0x40 Starts encryption keyed by an elliptic curve exchange at the Link Layer (7.0). 83 octets 7.0 2.4.2.59
LL_ENC_ECDH_RSP in LL Control PDU 0x41 The peripheral's public key and random value for the Link Layer key exchange (7.0). 83 octets 7.0 2.4.2.60
LL_HDT_CONFIG_REQ in LL Control PDU 0x42 Proposes payload window sizes for the High Data Throughput PHY (7.0). 2 octets 7.0 2.4.2.61
LL_HDT_CONFIG_RSP in LL Control PDU 0x43 Answers with this side's payload window sizes for HDT (7.0). 2 octets 7.0 2.4.2.61
LL_HDT_LQF_REPORTING_IND in LL Control PDU 0x44 Turns link quality reporting for HDT on or off (7.0). 2 octets 7.0 2.4.2.62
LL_CIG_CONFIG_REQ in LL Control PDU 0x45 Proposes a configuration for streams of a connected isochronous group (7.0). 5 octets 7.0 2.4.2.63
LL_CIG_CONFIG_RSP in LL Control PDU 0x46 Accepts a CIG configuration (7.0). 4 octets 7.0 2.4.2.64
LL_CIG_CONFIG_REMOVE_IND in LL Control PDU 0x47 Removes a CIG configuration (7.0). 4 octets 7.0 2.4.2.65
LL_CIS_PERIPHERAL_UPDATE_REQ in LL Control PDU 0x48 The peripheral asks to change a CIS's configuration (7.0). 8 octets 7.0 2.4.2.66
LL_CIS_UPDATE_REQ in LL Control PDU 0x49 The central changes the configuration of CISes in a group (7.0). 4 octets 7.0 2.4.2.67
LL_CIS_UPDATE_RSP in LL Control PDU 0x4A Accepts a CIS update (7.0). 3 octets 7.0 2.4.2.68
Isochronous PDU in LE Uncoded PHY packet An isochronous PDU of a CIS or BIS: header, a fixed-time payload, and a MIC when encrypted. 2-257 octets 5.2 2.6
CIS PDU header in Isochronous PDU The header of a connected isochronous PDU: acknowledgment bits, close and null flags, Length. 2 octets 5.2 2.6.1
BIS PDU header in Isochronous PDU The header of a broadcast isochronous PDU: control subevent sequence bits and Length. 2 octets 5.2 2.6.2
BIG Control PDU in Isochronous PDU A control PDU of a broadcast isochronous group: an opcode and its data. 1-251 octets 5.2 2.6.3
BIG_CHANNEL_MAP_IND in BIG Control PDU 0x00 Changes the channels a BIG uses, at an instant. 8 octets 5.2 2.6.3.1
BIG_TERMINATE_IND in BIG Control PDU 0x01 Ends a BIG, with a reason, at an instant. 4 octets 5.2 2.6.3.2
Public device address A public device address: an IEEE-assigned company identifier and a company-assigned part. 6 octets 4.0–4.2 1.3.1
Random device address A random device address, as 4.0 describes it: hash and random parts. 6 octets 4.0–4.0 1.3
Static device address A static random address: random bits with the two top bits set, kept until power cycle at least. 6 octets 4.2 1.3.2.1
Non-resolvable private address A non-resolvable private address: random bits with the two top bits clear, changed often. 6 octets 4.2 1.3.2.2
Resolvable private address A resolvable private address: a random part and a hash of it under an IRK, so bonded peers can resolve it. 6 octets 4.2 1.3.2.2
AdvA field in Extended Header The advertiser's address as an extended header field. 6 octets 5.0 2.3.4.1
TargetA field in Extended Header The target device's address as an extended header field. 6 octets 5.0 2.3.4.2
TxPower field in Extended Header The transmit power level, in dBm, as an extended header field. 1 octet 5.0 2.3.4.7
Decision data in ADV_DECISION_IND Decision data (6.0): a resolvable tag scanners can check, then arbitrary data. 0-N octets 6.0 2.3.1.11
Resolvable Tag in Decision data A resolvable tag: a hash and random value that a device with the key can verify. 6 octets 6.0 2.3.1.11
LE HDT PDU components in LE HDT PHY packet How HDT PDUs are composed of a first and a second PDU (7.0). 0-N octets 7.0 2.7
LE HDT PDU Header Zone in LE HDT PDU components The PDU header zone of an HDT packet (7.0). 2-N octets 7.0 2.7.2
LE HDT Rx Portion in LE HDT PDU Header Zone The receive portion of an HDT packet (7.0). 5-9 octets 7.0 2.7.2.2
LE HDT Tx Portion in LE HDT PDU Header Zone The transmit portion of an HDT packet (7.0). 1-25 octets 7.0 2.7.2.3
LE HDT LL Descriptor in LE HDT PDU Header Zone An HDT Link Layer descriptor (7.0). 5-6 octets 7.0 2.7.2.3
ISOAL 1
Segmentation header in Isochronous PDU The header ISOAL puts before each segment of a framed SDU: start or continuation, completion, length. 2 octets 5.2 2.2
Channel Sounding 1
CS_SYNC packet A Channel Sounding packet: preamble, access address and a sounding or random sequence for phase and time. 5.5-N octets 6.0 2
Test modes 13
Test command (transmitter, receiver) A two-octet test command over the test UART: start a transmitter or receiver test on a channel. 2 octets 4.0 3.3.2
Test command (setup, end) A two-octet test command to set up the test (length, PHY, modulation) or to end it. 2 octets 4.2 3.3.2
Test event A two-octet event from the device under test: a status or a packet report. 2 octets 4.0 3.4
LE_Test_Status event in Test event Reports success or failure of the last command. 2 octets 4.0 3.4.1
LE_Packet_Report event in Test event Reports how many test packets were received when a test ends. 2 octets 4.0 3.4.2
LE test packet (LE Uncoded PHYs) A test packet on the LE uncoded PHYs: like an LE packet, with a payload of a known pattern. 47-307 octets 4.1 4.1
LE test packet (LE Coded PHY) A test packet on the LE Coded PHY. 5.0 4.1
LE CS test packet A Channel Sounding test packet. 9.5-22.5 octets 6.0 4.1
LE test packet PDU in LE test packet (LE Uncoded PHYs) The test PDU: a header and the test payload. 2-N octets 4.1 4.1.4
LE test packet header in LE test packet PDU The test PDU header: payload pattern type, CTE flag and payload length. 2-3 octets 4.1 4.1.4
LE HDT test packet (short format, format 0) A short HDT test packet (7.0). 7.0 4.2
LE HDT test packet (format 1) An HDT test packet, format 1 (7.0). 7.0 4.2
UTP message An upper tester message: type, length and value (6.2 on). 3-N octets 6.2 5.2
Baseband 36
Basic Rate packet A Basic Rate packet: access code, header, then the payload; shorter packets stop after the code or header. 15.25-364.5 octets 4.1 6.1.1
Enhanced Data Rate packet An Enhanced Data Rate packet: access code and header at the basic rate, then a guard, a sync and the faster payload. 4.0 6.1.2
BD_ADDR The Bluetooth device address: lower address part, upper address part, non-significant part. 6 octets 4.1 1.2
Access code in Basic Rate packet The access code that starts each packet: a preamble, a sync word derived from a LAP, and a trailer. 8.5-9 octets 4.0 6.3
Packet header in Basic Rate packet The packet header: logical transport address, packet type, flow, ARQ and sequence bits, and an 8-bit HEC. 18 bits 4.1 6.4
Payload header (single-slot ACL) in Basic Rate packet The one-octet payload header of single-slot ACL packets: logical link, flow, and a 5-bit length. 1 octet 4.1–5.3 6.6.2
Payload header (multi-slot and EDR ACL) in Basic Rate packet The two-octet payload header of multi-slot and EDR ACL packets: logical link, flow, and a 10-bit length. 2 octets 4.0–5.3 6.6.2
NULL in Basic Rate packet 0b0000 A packet with no payload, used to acknowledge or keep timing. 4.0 6.5
POLL in Basic Rate packet 0b0001 Like NULL, but the peripheral has to answer it. 4.0 6.5
FHS in Basic Rate packet 0b0010 Carries the frequency hop synchronization payload, during paging and role switches. 20 octets 4.0 6.5
DM1 in Basic Rate packet 0b0011 One slot of ACL data with 2/3 FEC; also carries LMP on every link. 3-24 octets 4.0 6.5
2-DH1 in Basic Rate packet 0b0100 One slot of ACL data at 2 Mb/s (EDR). 4-62 octets 4.0 6.5
DH1 in Basic Rate packet 0b0100 One slot of ACL data without FEC. 3-34 octets 4.0 6.5
HV1 in Basic Rate packet 0b0101 SCO voice with 1/3 FEC, 10 octets, sent every second slot. 10 octets 4.0 6.5
2-EV3 in Basic Rate packet 0b0110 eSCO data in one slot at 2 Mb/s. 3-62 octets 4.0 6.5
HV2 in Basic Rate packet 0b0110 SCO voice with 2/3 FEC, 20 octets, sent every fourth slot. 20 octets 4.0 6.5
3-EV3 in Basic Rate packet 0b0111 eSCO data in one slot at 3 Mb/s. 3-92 octets 4.0 6.5
EV3 in Basic Rate packet 0b0111 eSCO data in one slot, with CRC and retransmission. 3-32 octets 4.0 6.5
HV3 in Basic Rate packet 0b0111 SCO voice without FEC, 30 octets, sent every sixth slot. 30 octets 4.0 6.5
3-DH1 in Basic Rate packet 0b1000 One slot of ACL data at 3 Mb/s (EDR). 4-91 octets 4.0 6.5
DV in Basic Rate packet 0b1000 Voice and data in one SCO packet. 13-22 octets 4.0 6.5
AUX1 in Basic Rate packet 0b1001 One slot of ACL data without CRC and never retransmitted. 1-30 octets 4.0 6.5
2-DH3 in Basic Rate packet 0b1010 Three slots of ACL data at 2 Mb/s (EDR). 4-375 octets 4.0 6.5
DM3 in Basic Rate packet 0b1010 Three slots of ACL data with 2/3 FEC. 4-129 octets 4.0 6.5
3-DH3 in Basic Rate packet 0b1011 Three slots of ACL data at 3 Mb/s (EDR). 4-560 octets 4.0 6.5
DH3 in Basic Rate packet 0b1011 Three slots of ACL data without FEC. 4-191 octets 4.0 6.5
2-EV5 in Basic Rate packet 0b1100 eSCO data in up to three slots at 2 Mb/s. 3-362 octets 4.0 6.5
EV4 in Basic Rate packet 0b1100 eSCO data in up to three slots with 2/3 FEC. 3-122 octets 4.0 6.5
3-EV5 in Basic Rate packet 0b1101 eSCO data in up to three slots at 3 Mb/s. 3-542 octets 4.0 6.5
EV5 in Basic Rate packet 0b1101 eSCO data in up to three slots without FEC. 3-182 octets 4.0 6.5
2-DH5 in Basic Rate packet 0b1110 Five slots of ACL data at 2 Mb/s (EDR). 4-687 octets 4.0 6.5
DM5 in Basic Rate packet 0b1110 Five slots of ACL data with 2/3 FEC. 4-232 octets 4.0 6.5
3-DH5 in Basic Rate packet 0b1111 Five slots of ACL data at 3 Mb/s (EDR). 4-1029 octets 4.0 6.5
DH5 in Basic Rate packet 0b1111 Five slots of ACL data without FEC. 4-347 octets 4.0 6.5
FHS payload in FHS The FHS payload: the sender's address, class of device and clock, for paging and role switches. 18 octets 4.1 6.5.1.4
DV payload in DV The DV packet's payload: a voice field and a data field in one packet. 21.375-44.5 octets 4.0 6.5.2.4
LMP 93
LMP_NAME_REQ formerly LMP_name_req 0x01 Asks for a fragment of the peer's device name. 2 octets 4.0 5.1
LMP_NAME_RES formerly LMP_name_res 0x02 Carries a fragment of the device name and its total length. 17 octets 4.0 5.1
LMP_ACCEPTED formerly LMP_accepted 0x03 Accepts the PDU whose opcode it names. 2 octets 4.0 5.1
LMP_NOT_ACCEPTED formerly LMP_not_accepted 0x04 Rejects the PDU whose opcode it names, with a reason. 3 octets 4.0 5.1
LMP_CLKOFFSET_REQ formerly LMP_clkoffset_req 0x05 Asks for the clock offset between the peripheral and the central. 1 octet 4.0 5.1
LMP_CLKOFFSET_RES formerly LMP_clkoffset_res 0x06 Answers with the clock offset. 3 octets 4.0 5.1
LMP_DETACH formerly LMP_detach 0x07 Closes the connection, with a reason. 2 octets 4.0 5.1
LMP_IN_RAND formerly LMP_in_rand 0x08 Sends the random number for an initialization key (legacy pairing). 17 octets 4.0 5.1
LMP_COMB_KEY formerly LMP_comb_key 0x09 Sends a random number for a combination key (legacy pairing). 17 octets 4.0 5.1
LMP_UNIT_KEY formerly LMP_unit_key 0x0A Sends a unit key (legacy pairing, deprecated). 17 octets 4.0 5.1
LMP_AU_RAND formerly LMP_au_rand 0x0B A challenge for authentication. 17 octets 4.0 5.1
LMP_SRES formerly LMP_sres 0x0C The answer to an authentication challenge. 5 octets 4.0 5.1
LMP_TEMP_RAND formerly LMP_temp_rand 0x0D A random number for a temporary broadcast key. 17 octets 4.0 5.1
LMP_TEMP_KEY formerly LMP_temp_key 0x0E The temporary broadcast key, masked. 17 octets 4.0 5.1
LMP_ENCRYPTION_MODE_REQ formerly LMP_encryption_mode_req 0x0F Asks to switch encryption on or off. 2 octets 4.0 5.1
LMP_ENCRYPTION_KEY_SIZE_REQ formerly LMP_encryption_key_size_req 0x10 Proposes the encryption key size. 2 octets 4.0 5.1
LMP_START_ENCRYPTION_REQ formerly LMP_start_encryption_req 0x11 Starts encryption, with the random number for the key. 17 octets 4.0 5.1
LMP_STOP_ENCRYPTION_REQ formerly LMP_stop_encryption_req 0x12 Stops encryption. 1 octet 4.0 5.1
LMP_SWITCH_REQ formerly LMP_switch_req 0x13 Asks for a role switch at an instant. 5 octets 4.0 5.1
LMP_HOLD formerly LMP_hold 0x14 Puts the link on hold, from an instant for a time. 7 octets 4.0 5.1
LMP_HOLD_REQ formerly LMP_hold_req 0x15 Asks to put the link on hold. 7 octets 4.0 5.1
LMP_SNIFF_REQ formerly LMP_sniff_req 0x17 Asks for sniff mode: the anchor offset, interval, attempt and timeout. 10 octets 4.0 5.1
LMP_UNSNIFF_REQ formerly LMP_unsniff_req 0x18 Asks to leave sniff mode. 1 octet 4.0 5.1
LMP_park_req 0x19 Asks to park the peripheral (park state was removed in 5.0). 17 octets 4.0–4.2 5.1
LMP_set_broadcast_scan_window 0x1B Sets a broadcast scan window for parked peripherals. 6 octets 4.0–4.2 5.1
LMP_modify_beacon 0x1C Changes the beacon parameters of parked peripherals. 13 octets 4.0–4.2 5.1
LMP_unpark_BD_ADDR_req 0x1D Unparks peripherals by their device address. 17 octets 4.0–4.2 5.1
LMP_unpark_PM_ADDR_req 0x1E Unparks peripherals by their parked member address. 15 octets 4.0–4.2 5.1
LMP_INCR_POWER_REQ formerly LMP_incr_power_req 0x1F Asks the peer to raise its transmit power by one step. 2 octets 4.0 5.1
LMP_DECR_POWER_REQ formerly LMP_decr_power_req 0x20 Asks the peer to lower its transmit power by one step. 2 octets 4.0 5.1
LMP_MAX_POWER formerly LMP_max_power 0x21 Says the transmit power is already at its maximum. 1 octet 4.0 5.1
LMP_MIN_POWER formerly LMP_min_power 0x22 Says the transmit power is already at its minimum. 1 octet 4.0 5.1
LMP_AUTO_RATE formerly LMP_auto_rate 0x23 Lets the peer choose between packets with and without FEC by link quality. 1 octet 4.0 5.1
LMP_PREFERRED_RATE formerly LMP_preferred_rate 0x24 Says which data rate and packet size the sender prefers. 2 octets 4.0 5.1
LMP_VERSION_REQ formerly LMP_version_req 0x25 Sends this side's LMP version, company and subversion, and asks for the peer's. 6 octets 4.0 5.1
LMP_VERSION_RES formerly LMP_version_res 0x26 Answers with this side's version, company and subversion. 6 octets 4.0 5.1
LMP_FEATURES_REQ formerly LMP_features_req 0x27 Sends this side's supported features (page 0) and asks for the peer's. 9 octets 4.0 5.1
LMP_FEATURES_RES formerly LMP_features_res 0x28 Answers with this side's features. 9 octets 4.0 5.1
LMP_QUALITY_OF_SERVICE formerly LMP_quality_of_service 0x29 The central sets the poll interval and broadcast retransmissions. 4 octets 4.0 5.1
LMP_QUALITY_OF_SERVICE_REQ formerly LMP_quality_o f_service_req, LMP_quality_of_service_req 0x2A Asks for a poll interval and broadcast retransmissions. 4 octets 4.0 5.1
LMP_SCO_LINK_REQ formerly LMP_SCO_link_req 0x2B Sets up an SCO link: handle, timing, packet type, air mode. 7 octets 4.0 5.1
LMP_REMOVE_SCO_LINK_REQ formerly LMP_remove_SCO_link_req 0x2C Removes an SCO link, with a reason. 3 octets 4.0 5.1
LMP_MAX_SLOT formerly LMP_max_slot 0x2D Sets the most slots the peer may use per packet. 2 octets 4.0 5.1
LMP_MAX_SLOT_REQ formerly LMP_max_slot_req 0x2E Asks to allow packets of more slots. 2 octets 4.0 5.1
LMP_TIMING_ACCURACY_REQ formerly LMP_timing_accuracy_req 0x2F Asks for the peer's clock drift and jitter. 1 octet 4.0 5.1
LMP_TIMING_ACCURACY_RES formerly LMP_timing_accuracy_res 0x30 Answers with clock drift and jitter. 3 octets 4.0 5.1
LMP_SETUP_COMPLETE formerly LMP_setup_complet e, LMP_setup_complete 0x31 Says this side has finished setting up the link. 1 octet 4.0 5.1
LMP_USE_SEMI_PERMANENT_KEY formerly LMP_use_semi_permanent_key 0x32 Switches to the semi-permanent link key. 1 octet 4.0 5.1
LMP_HOST_CONNECTION_REQ formerly LMP_host_connecti on_req, LMP_host_connection_req 0x33 Asks whether the peer's Host accepts the connection. 1 octet 4.0 5.1
LMP_SLOT_OFFSET formerly LMP_slot_offset 0x34 Sends the slot offset between the two piconets before a role switch. 9 octets 4.0 5.1
LMP_PAGE_MODE_REQ formerly LMP_page_mode_req 0x35 Suggests a paging scheme for future paging. 3 octets 4.0 5.1
LMP_PAGE_SCAN_MODE_REQ formerly LMP_page_scan_mode_req 0x36 Asks the peer to use a page scan scheme. 3 octets 4.0 5.1
LMP_SUPERVISION_TIMEOUT formerly LMP_supervision_timeout 0x37 Sets the link supervision timeout. 3 octets 4.0 5.1
LMP_TEST_ACTIVATE formerly LMP_test_activate 0x38 Enters test mode. 1 octet 4.0 5.1
LMP_TEST_CONTROL formerly LMP_test_control 0x39 Configures a test: scenario, hopping, frequencies, power, packet type. 10 octets 4.0 5.1
LMP_ENCRYPTION_KEY_SIZE_MASK_REQ formerly LMP_encryption_key_size_mask_req 0x3A Asks which encryption key sizes the peer supports for broadcast. 1 octet 4.0 5.1
LMP_ENCRYPTION_KEY_SIZE_MASK_RES formerly LMP_encryption_key_size_mask_res 0x3B Answers with a bit mask of supported key sizes. 3 octets 4.0 5.1
LMP_SET_AFH formerly LMP_set_AFH 0x3C Switches adaptive frequency hopping on or off with a channel map, at an instant. 16 octets 4.0 5.1
LMP_ENCAPSULATED_HEADER formerly LMP_encapsulated_header 0x3D Announces an encapsulated payload, such as a public key, and its length. 4 octets 4.0 5.1
LMP_ENCAPSULATED_PAYLOAD formerly LMP_encapsulated_payload 0x3E Carries 16 octets of an encapsulated payload. 17 octets 4.0 5.1
LMP_SIMPLE_PAIRING_CONFIRM formerly LMP_Simple_Pairing_Confirm 0x3F A commitment in Secure Simple Pairing. 17 octets 4.0 5.1
LMP_SIMPLE_PAIRING_NUMBER formerly LMP_Simple_Pairing_Number 0x40 A nonce in Secure Simple Pairing. 17 octets 4.0 5.1
LMP_DHKEY_CHECK formerly LMP_DHkey_Check 0x41 Proves knowledge of the Diffie-Hellman key in Secure Simple Pairing. 17 octets 4.0 5.1
LMP_PAUSE_ENCRYPTION_AES_REQ formerly LMP_pause_encryption_aes_req 0x42 Pauses AES encryption to refresh the key (4.1 on). 17 octets 4.1 5.1
LMP_ACCEPTED_EXT formerly LMP_accepted_ext 0x01 Accepts the extended PDU it names. 4 octets 4.0 5.1
LMP_NOT_ACCEPTED_EXT formerly LMP_not_accepted_ext 0x02 Rejects the extended PDU it names, with a reason. 5 octets 4.0 5.1
LMP_FEATURES_REQ_EXT formerly LMP_features_req_ext 0x03 Sends one page of extended features and asks for the peer's. 12 octets 4.0 5.1
LMP_FEATURES_RES_EXT formerly LMP_features_res_ext 0x04 Answers with one page of extended features. 12 octets 4.0 5.1
LMP_CLK_ADJ formerly LMP_clk_adj 0x05 The central adjusts the piconet clock (4.1 on). 15 octets 4.1 5.1
LMP_CLK_ADJ_ACK formerly LMP_clk_adj_ack 0x06 Acknowledges a clock adjustment. 3 octets 4.1 5.1
LMP_CLK_ADJ_REQ formerly LMP_clk_adj_req 0x07 The peripheral asks for a clock adjustment. 6 octets 4.1 5.1
LMP_PACKET_TYPE_TABLE_REQ formerly LMP_packet_type_table_req 0x0B Switches between basic rate and EDR packet types. 3 octets 4.0 5.1
LMP_eSCO_LINK_REQ formerly LMP_eSCO_link_req 0x0C Sets up or changes an eSCO link: handle, timing, packet types and lengths, air mode. 16 octets 4.0 5.1
LMP_REMOVE_eSCO_LINK_REQ ¶ formerly LMP_remove_eSCO_link_req see Note 4 on page 319, LMP_remove_eSCO_link_req see Note 4 on page 357, LMP_remove_eSCO_link_req, LMP_REMOVE_eSCO_LINK_REQ 0x0D Removes an eSCO link, with a reason. 4 octets 4.0 5.1
LMP_CHANNEL_CLASSIFICATION_REQ formerly LMP_channel_classification_req 0x10 Asks the peripheral to report channel classification for AFH. 7 octets 4.0 5.1
LMP_CHANNEL_CLASSIFICATION formerly LMP_channel_classification 0x11 Reports which channels the peripheral finds good or bad. 12 octets 4.0 5.1
LMP_SNIFF_SUBRATING_REQ formerly LMP_sniff_subrating_req 0x15 Proposes sniff subrating. 9 octets 4.0 5.1
LMP_SNIFF_SUBRATING_RES formerly LMP_sniff_subrating_res 0x16 Answers a sniff subrating proposal. 9 octets 4.0 5.1
LMP_PAUSE_ENCRYPTION_REQ formerly LMP_pause_encryption_req 0x17 Pauses encryption to change the key. 2 octets 4.0 5.1
LMP_RESUME_ENCRYPTION_REQ formerly LMP_resume_encry ption_req, LMP_resume_encryption_req 0x18 Resumes encryption after a pause. 2 octets 4.0 5.1
LMP_IO_CAPABILITY_REQ formerly LMP_IO_Capability_req 0x19 Sends the IO capabilities and authentication requirements for Secure Simple Pairing. 5 octets 4.0 5.1
LMP_IO_CAPABILITY_RES formerly LMP_IO_Capability_res 0x1A Answers with this side's IO capabilities and requirements. 5 octets 4.0 5.1
LMP_NUMERIC_COMPARISON_FAILED formerly LMP_numeric_comparison_failed 0x1B Says the numeric comparison failed. 2 octets 4.0 5.1
LMP_PASSKEY_FAILED formerly LMP_passkey_failed 0x1C Says the passkey entry failed. 2 octets 4.0 5.1
LMP_OOB_FAILED formerly LMP_oob_failed 0x1D Says the out-of-band pairing failed. 2 octets 4.0 5.1
LMP_KEYPRESS_NOTIFICATION formerly LMP_keypress_notification 0x1E Reports keypresses during passkey entry. 3 octets 4.0 5.1
LMP_POWER_CONTROL_REQ formerly LMP_power_control_req 0x1F Asks the peer to change its transmit power, for EDR power control. 3 octets 4.0 5.1
LMP_POWER_CONTROL_RES formerly LMP_power_control_res 0x20 Answers a power control request. 3 octets 4.0 5.1
LMP_PING_REQ formerly LMP_ping_req 0x21 Asks for a reply, to check that the encrypted link still authenticates (4.1 on). 2 octets 4.1 5.1
LMP_PING_RES formerly LMP_ping_res 0x22 Answers a ping. 2 octets 4.1 5.1
LMP_SAM_SET_TYPE0 formerly LMP_SAM_set_type0 0x23 Slot availability masks: sets the type-0 submap (5.0 on). 17 octets 5.0 5.1
LMP_SAM_DEFINE_MAP formerly LMP_SAM_define_map 0x24 Slot availability masks: defines a map of available slots. 17 octets 5.0 5.1
LMP_SAM_SWITCH formerly LMP_SAM_switch 0x25 Slot availability masks: switches to a defined map at an instant. 9 octets 5.0 5.1
HCI 25
UART packet An HCI packet on a UART (H4): one indicator octet that says which kind of HCI packet follows. 1-N octets 4.0 2
HCI Command packet in UART packet 0x01 A command from the Host to the Controller: a 16-bit opcode, the length of the parameters, the parameters. 3-N octets 4.0 5.4.1
HCI ACL Data packet in UART packet 0x02 ACL data between Host and Controller: connection handle, flags, length, then a fragment of an L2CAP PDU. 4-N octets 4.0 5.4.2
HCI Synchronous Data packet in UART packet 0x03 SCO or eSCO data between Host and Controller: connection handle, status flags, length, the samples. 3.25-N octets 4.0 5.4.3
HCI Event packet in UART packet 0x04 An event from the Controller to the Host: an event code, the length of the parameters, the parameters. 2-N octets 4.0 5.4.4
HCI ISO Data packet in UART packet 0x05 Isochronous data between Host and Controller (5.2 on): handle, flags, length, an optional time stamp, an SDU fragment. 12.125-N octets 5.2 5.4.5
HCI command opcode in HCI Command packet The command opcode split into its two parts: the command within its group, and the group. 2 octets 4.0 5.4.1
Three-wire UART packet A Three-wire UART packet: a 4-octet header, the payload, an optional CRC; SLIP framing around it. 6-4101 octets 4.0 4
Three-wire UART packet header in Three-wire UART packet The Three-wire UART header: sequence and acknowledgment numbers, flags, packet type, length, checksum. 4 octets 4.0 4
Acknowledgment packets in Three-wire UART packet · formerly Acknowledgement Packets, Acknowledgment Packets 0b0000 A packet that only acknowledges; it has no payload. 0-4095 octets 4.0 4.5
HCI Command packet in Three-wire UART packet · formerly HCI Command Packet 0b0001 An HCI command carried by the Three-wire UART. 0-4095 octets 4.0 4.5
HCI ACL Data packet in Three-wire UART packet · formerly HCI ACL Data Packet 0b0010 HCI ACL data carried by the Three-wire UART. 0-4095 octets 4.0 4.5
HCI Synchronous Data packet in Three-wire UART packet · formerly HCI Synchronous Data Packet 0b0011 HCI synchronous data carried by the Three-wire UART. 0-4095 octets 4.0 4.5
HCI Event packet in Three-wire UART packet · formerly HCI Event Packet 0b0100 An HCI event carried by the Three-wire UART. 0-4095 octets 4.0 4.5
HCI ISO Data packet in Three-wire UART packet 0b0101 HCI ISO data carried by the Three-wire UART (5.2 on). 0-4095 octets 5.2 4.5
Vendor Specific in Three-wire UART packet 0b1110 Vendor-specific payload. 0-4095 octets 4.0 4.5
Link Control packet in Three-wire UART packet · formerly Link Control Packet 0b1111 A link control message of the Three-wire UART itself: sync, configuration, sleep and wakeup. 0-4095 octets 4.0 4.5
SYNC message in Link Control packet Link establishment: sent until the peer answers, to find out it is there. 2 octets 4.0 8.4
SYNC RESPONSE message in Link Control packet Answers a SYNC message. 2 octets 4.0 8.5
CONFIG message in Link Control packet Link establishment: proposes the link's configuration (window size, CRC, flow control). 3 octets 4.0 8.6
CONFIG RESPONSE message in Link Control packet Answers a CONFIG message with the configuration both will use. 3 octets 4.0 8.7
Configuration field in CONFIG message The configuration octets of CONFIG and CONFIG RESPONSE: sliding window size and options. 1 octet 4.0 8.8
WAKEUP message in Link Control packet Asks a sleeping peer to wake up. 2 octets 4.0 9.1
WOKEN message in Link Control packet Says this side is awake. 2 octets 4.0 9.2
SLEEP message in Link Control packet Says this side is going to sleep. 2 octets 4.0 9.3
L2CAP 49
B-frame The basic L2CAP frame: a length, a channel identifier and the payload. 4-65539 octets 4.0 3.1
G-frame A frame on the connectionless channel: basic header, then the PSM of the receiving service. 6-N octets 4.0 3.2
K-frame A frame of an LE credit-based channel; the first of an SDU starts with the SDU's length. 6-65541 octets 4.1–5.0 3.4
C-frame A control frame: the basic header on a signaling channel, then one or more commands. 4-N octets 4.0 4
Signaling command in C-frame A signaling command: code, identifier, data length, then the command's data. 4-N octets 4.0 4
L2CAP_COMMAND_REJECT_RSP in Signaling command · formerly Command Reject 0x01 Answers a command that was not understood or not acceptable. 6-N octets 4.0 4.1
L2CAP_CONNECTION_REQ in Signaling command · formerly Connection Request 0x02 Asks to open a channel to a service (BR/EDR). 8-N octets 4.0 4.2
L2CAP_CONNECTION_RSP in Signaling command · formerly Connection Response 0x03 Answers a connection request: the new channel's endpoint, or why not (yet). 12 octets 4.0 4.3
L2CAP_CONFIGURATION_REQ in Signaling command · formerly Configuration Request 0x04 Proposes options for a channel, such as the MTU or retransmission mode (BR/EDR). 12 octets 4.0 4.4
L2CAP_CONFIGURATION_RSP in Signaling command · formerly Configuration Response 0x05 Answers a configuration request, accepting or countering its options. 12 octets 4.0 4.5
L2CAP_DISCONNECTION_REQ in Signaling command · formerly Disconnection Request 0x06 Asks to close a channel. 8 octets 4.0 4.6
L2CAP_DISCONNECTION_RSP in Signaling command · formerly Disconnection Response 0x07 Confirms that a channel is closed. 8 octets 4.0 4.7
L2CAP_ECHO_REQ in Signaling command · formerly Echo Request 0x08 Asks for an echo, to test the link. 4-N octets 4.0 4.8
L2CAP_ECHO_RSP in Signaling command · formerly Echo Response 0x09 Answers an echo request. 4-N octets 4.0 4.9
L2CAP_INFORMATION_REQ in Signaling command · formerly Information Request 0x0A Asks for information about the peer's L2CAP: MTU, extended features or fixed channels. 6 octets 4.0 4.10
L2CAP_INFORMATION_RSP in Signaling command · formerly Information Response 0x0B Answers an information request. 8-N octets 4.0 4.11
L2CAP_CREATE_CHANNEL_REQ in Signaling command · formerly Create Channel Request 0x0C Opens a channel on an AMP controller (removed after 5.2, with AMP). 9-N octets 4.0–5.2 4.14
L2CAP_CREATE_CHANNEL_RSP in Signaling command · formerly Create Channel Response 0x0D Answers a create channel request (AMP). 12 octets 4.0–5.2 4.15
L2CAP_MOVE_CHANNEL_REQ in Signaling command · formerly Move Channel Request 0x0E Asks to move a channel to another controller (AMP). 7 octets 4.0–5.2 4.16
L2CAP_MOVE_CHANNEL_RSP in Signaling command · formerly Move Channel Response 0x0F Answers a move channel request (AMP). 8 octets 4.0–5.2 4.17
L2CAP_MOVE_CHANNEL_CONFIRMATION_REQ in Signaling command · formerly Move Channel Confirmation 0x10 Confirms the outcome of a channel move (AMP). 8 octets 4.0–5.2 4.18
L2CAP_MOVE_CHANNEL_CONFIRMATION_RSP in Signaling command · formerly Move Channel Confirmation Response 0x11 Acknowledges a move confirmation (AMP). 6 octets 4.0–5.2 4.19
L2CAP_CONNECTION_PARAMETER_UPDATE_REQ in Signaling command · formerly Connection Parameter Update Request 0x12 The LE peripheral asks the central for new connection parameters. 12 octets 4.0 4.20
L2CAP_CONNECTION_PARAMETER_UPDATE_RSP in Signaling command · formerly Connection Parameter Update Response 0x13 The central accepts or rejects the requested connection parameters. 6 octets 4.0 4.21
L2CAP_LE_CREDIT_BASED_CONNECTION_REQ in Signaling command · formerly LE Credit Based Connection Request 0x14 Asks to open an LE credit-based channel (4.1 on). 14 octets 4.1 4.22
L2CAP_LE_CREDIT_BASED_CONNECTION_RSP in Signaling command · formerly LE Credit Based Connection Response 0x15 Answers an LE credit-based connection request. 14 octets 4.1 4.23
L2CAP_FLOW_CONTROL_CREDIT_IND in Signaling command · formerly LE Flow Control Credit 0x16 Grants the peer more credits on a credit-based channel. 8 octets 4.1 4.24
L2CAP_CREDIT_BASED_CONNECTION_REQ in Signaling command 0x17 Asks to open up to five enhanced credit-based channels at once (5.2 on). 16-24 octets 5.2 4.25
L2CAP_CREDIT_BASED_CONNECTION_RSP in Signaling command 0x18 Answers an enhanced credit-based connection request, channel by channel. 16-24 octets 5.2 4.26
L2CAP_CREDIT_BASED_RECONFIGURE_REQ in Signaling command 0x19 Changes the MTU and MPS of enhanced credit-based channels. 12-20 octets 5.2 4.27
L2CAP_CREDIT_BASED_RECONFIGURE_RSP in Signaling command 0x1A Answers a reconfiguration request. 6 octets 5.2 4.28
Configuration option in L2CAP_CONFIGURATION_REQ A configuration option: type, length, then data; options follow each other in a configuration command. 2-4 octets 4.0 5
Maximum Transmission Unit (MTU) in Configuration option 0x01 The largest SDU the sender can receive on the channel. 4 octets 4.0 5.1
Flush Timeout option in Configuration option · formerly Flush Timeout Option 0x02 How long the sender's controller keeps trying to deliver data before flushing it. 4 octets 4.0 5.2
Quality of Service (QoS) option in Configuration option · formerly Quality of Service (QoS) Option 0x03 Quality of service the sender asks for: service type, token rate, bandwidth, latency. 24 octets 4.0 5.3
Retransmission and Flow Control option in Configuration option · formerly Retransmission and Flow Control Option 0x04 Chooses basic, retransmission, flow control, enhanced retransmission or streaming mode, with timers and windows. 11 octets 4.0 5.4
Frame Check Sequence (FCS) option in Configuration option · formerly Frame Check Sequence (FCS) Option 0x05 Whether frames carry a frame check sequence. 3 octets 4.0 5.5
Extended Flow Specification option in Configuration option · formerly Extended Flow Specification Option 0x06 An extended flow specification, for guaranteed or best-effort traffic. 18 octets 4.0 5.6
Extended Window Size option in Configuration option · formerly Extended Window Size Option 0x07 A transmit window larger than the retransmission option allows. 4 octets 4.0 5.7
Configuration Request flags in L2CAP_CONFIGURATION_REQ The flags of a configuration request: whether more requests continue it. 2 octets 4.0–5.1 4.4
Configuration Response flags in L2CAP_CONFIGURATION_RSP The flags of a configuration response: whether more responses continue it. 2 octets 4.0–5.1 4.5
I-frame in B-frame An information frame of the retransmission, flow control and streaming modes: header, control field, data, check. 6-65547 octets 4.0 3.3
I-frame Enhanced Control Field in I-frame The 16-bit control field of an I-frame in enhanced retransmission and streaming modes. 2 octets 4.0 3.3.2
I-frame Extended Control Field in I-frame The 32-bit control field of an I-frame, with 14-bit sequence numbers for larger windows. 4 octets 4.0 3.3.2
I-frame Standard Control Field in I-frame The 16-bit control field of an I-frame in retransmission and flow control modes. 2 octets 4.0 3.3.2
S-frame in B-frame A supervisory frame: acknowledges I-frames or asks for retransmission; it carries no data. 6-10 octets 4.0 3.3
S-frame Enhanced Control Field in S-frame The 16-bit control field of an S-frame in enhanced retransmission mode, with Poll and Final bits. 2 octets 4.0 3.3.2
S-frame Extended Control Field in S-frame The 32-bit control field of an S-frame, with a 14-bit sequence number. 4 octets 4.0 3.3.2
S-frame Standard Control Field in S-frame The 16-bit control field of an S-frame in retransmission and flow control modes. 2 octets 4.0 3.3.2
SDP 9
SDP PDU in B-frame An SDP PDU: an ID, a transaction ID, the length of the parameters, the parameters. 5-N octets 4.0 4.2
SDP_ERROR_RSP in SDP PDU · formerly SDP_ErrorResponse 0x01 Says a request was invalid, with an error code. 7 octets 4.0 4.4.1
SDP_SERVICE_SEARCH_REQ in SDP PDU · formerly SDP_ServiceSearchRequest 0x02 Asks for the handles of service records matching a pattern of UUIDs. 4.0 4.5.1
SDP_SERVICE_SEARCH_RSP in SDP PDU · formerly SDP_ServiceSearchResponse 0x03 Answers with service record handles. 4.0 4.5.2
SDP_SERVICE_ATTR_REQ in SDP PDU · formerly SDP_ServiceAttributeRequest 0x04 Asks for attributes of one service record. 4.0 4.6.1
SDP_SERVICE_ATTR_RSP in SDP PDU · formerly SDP_ServiceAttributeResponse 0x05 Answers with the attributes of the record. 4.0 4.6.2
SDP_SERVICE_SEARCH_ATTR_REQ in SDP PDU · formerly SDP_ServiceSearchAttributeRequest 0x06 Searches by UUID pattern and reads attributes in one exchange. 4.0 4.7.1
SDP_SERVICE_SEARCH_ATTR_RSP in SDP PDU · formerly SDP_ServiceSearchAttributeResponse 0x07 Answers with the attributes of every matching record. 4.0 4.7.2
Data element An SDP data element: a type and size descriptor, then the value; sequences nest elements. 1-N octets 4.0 3.4
ATT 32
Attribute PDU in B-frame 0x0004 An Attribute Protocol PDU: an opcode, then the parameters of that PDU. 1-N octets 4.0 3.3.1
ATT_ERROR_RSP in Attribute PDU · formerly Error Response 0x01 Says a request failed: which request, at which handle, and why. 5 octets 4.0 3.4.1.1
ATT_EXCHANGE_MTU_REQ in Attribute PDU · formerly Exchange MTU Request 0x02 The client announces the largest ATT PDU it can receive. 3 octets 4.0 3.4.2.1
ATT_EXCHANGE_MTU_RSP in Attribute PDU · formerly Exchange MTU Response 0x03 The server announces the largest ATT PDU it can receive; both then use the smaller. 3 octets 4.0 3.4.2.2
ATT_FIND_INFORMATION_REQ in Attribute PDU · formerly Find Information Request 0x04 Asks for the handles and types of attributes in a range. 5 octets 4.0 3.4.3.1
ATT_FIND_INFORMATION_RSP in Attribute PDU · formerly Find Information Response 0x05 Lists handle and type pairs, all with 16-bit or all with 128-bit UUIDs. 6-N octets 4.0 3.4.3.2
ATT_FIND_BY_TYPE_VALUE_REQ in Attribute PDU · formerly Find By Type Value Request 0x06 Finds attributes of a 16-bit type with a given value, such as services of one UUID. 7-N octets 4.0 3.4.3.3
ATT_FIND_BY_TYPE_VALUE_RSP in Attribute PDU · formerly Find By Type Value Response 0x07 Lists the handle ranges of the attributes found. 5-N octets 4.0 3.4.3.4
ATT_READ_BY_TYPE_REQ in Attribute PDU · formerly Read By Type Request 0x08 Reads the values of all attributes of a type in a range, such as characteristic declarations. 7-21 octets 4.0 3.4.4.1
ATT_READ_BY_TYPE_RSP in Attribute PDU · formerly Read By Type Response 0x09 Lists handle and value pairs of the attributes read. 4-N octets 4.0 3.4.4.2
ATT_READ_REQ in Attribute PDU · formerly Read Request 0x0A Reads the value of one attribute. 3 octets 4.0 3.4.4.3
ATT_READ_RSP in Attribute PDU · formerly Read Response 0x0B Carries the value read, or as much of it as fits. 1-N octets 4.0 3.4.4.4
ATT_READ_BLOB_REQ in Attribute PDU · formerly Read Blob Request 0x0C Reads a long attribute value from an offset. 5 octets 4.0 3.4.4.5
ATT_READ_BLOB_RSP in Attribute PDU · formerly Read Blob Response 0x0D Carries the part of the value from the offset. 1-N octets 4.0 3.4.4.6
ATT_READ_MULTIPLE_REQ in Attribute PDU · formerly Read Multiple Request 0x0E Reads several attributes of known fixed length at once. 5-N octets 4.0 3.4.4.7
ATT_READ_MULTIPLE_RSP in Attribute PDU · formerly Read Multiple Response 0x0F Carries the values read, one after the other without lengths. 1-N octets 4.0 3.4.4.8
ATT_READ_BY_GROUP_TYPE_REQ in Attribute PDU · formerly Read by Group Type Request 0x10 Reads grouping attributes of a type in a range; used to discover primary services. 7-21 octets 4.0 3.4.4.9
ATT_READ_BY_GROUP_TYPE_RSP in Attribute PDU · formerly Read by Group Type Response 0x11 Lists each group's handle range and value. 6-N octets 4.0 3.4.4.10
ATT_WRITE_REQ in Attribute PDU · formerly Write Request 0x12 Writes an attribute value and asks for confirmation. 3-N octets 4.0 3.4.5.1
ATT_WRITE_RSP in Attribute PDU · formerly Write Response 0x13 Confirms a write. 1 octet 4.0 3.4.5.2
ATT_PREPARE_WRITE_REQ in Attribute PDU · formerly Prepare Write Request 0x16 Queues a part of a value for a long or reliable write. 5-N octets 4.0 3.4.6.1
ATT_PREPARE_WRITE_RSP in Attribute PDU · formerly Prepare Write Response 0x17 Echoes the queued part, so the client can check it. 5-N octets 4.0 3.4.6.2
ATT_EXECUTE_WRITE_REQ in Attribute PDU · formerly Execute Write Request 0x18 Writes or cancels all queued parts. 2 octets 4.0 3.4.6.3
ATT_EXECUTE_WRITE_RSP in Attribute PDU · formerly Execute Write Response 0x19 Confirms the queued writes were executed or cancelled. 1 octet 4.0 3.4.6.4
ATT_HANDLE_VALUE_NTF in Attribute PDU · formerly Handle Value Notification 0x1B The server sends an attribute value unasked, without acknowledgment. 3-N octets 4.0 3.4.7.1
ATT_HANDLE_VALUE_IND in Attribute PDU · formerly Handle Value Indication 0x1D The server sends an attribute value unasked and waits for a confirmation. 3-N octets 4.0 3.4.7.2
ATT_HANDLE_VALUE_CFM in Attribute PDU · formerly Handle Value Confirmation 0x1E The client confirms an indication. 1 octet 4.0 3.4.7.3
ATT_READ_MULTIPLE_VARIABLE_REQ in Attribute PDU 0x20 Reads several attributes of any length at once (5.2 on). 5-N octets 5.2 3.4.4.11
ATT_READ_MULTIPLE_VARIABLE_RSP in Attribute PDU 0x21 Carries the values read, each with its length. 5-N octets 5.2 3.4.4.12
ATT_MULTIPLE_HANDLE_VALUE_NTF in Attribute PDU 0x23 Notifies several attribute values in one PDU, each with handle and length (5.2 on). 9-N octets 5.2 3.4.7.4
ATT_WRITE_CMD in Attribute PDU · formerly Write Command, Write command 0x52 Writes an attribute value without asking for a response. 3-N octets 4.0 3.4.5.3
ATT_SIGNED_WRITE_CMD in Attribute PDU · formerly Signed Write Command, Signed Write command 0xD2 Writes without response, signed with a key from pairing; removed in 6.3. 15-N octets 4.0–6.2 3.4.5.4
GATT 8
Characteristic declaration value The value of a characteristic declaration: properties, the handle of the value, and its UUID. 5-19 octets 4.0 3.3.1
Characteristic Properties in Characteristic declaration value What a characteristic allows: broadcast, read, write with or without response, notify, indicate, signed write. 1 octet 4.0 3.3.1.1
Characteristic Extended Properties More characteristic properties: reliable write and writable descriptors. 2 octets 4.0 3.3.3.1
Client Characteristic Configuration Written by a client to switch notifications or indications of a characteristic on or off. 2 octets 4.0 3.3.3.3
Server Characteristic Configuration Written by a client to switch the broadcasting of a characteristic on or off. 2 octets 4.0 3.3.3.4
Characteristic Presentation Format Describes how to present a characteristic's value: data type, exponent, unit. 7 octets 4.0 3.3.3.5
Client Supported Features The GATT features a client supports, such as robust caching and EATT. 1 octet 5.1 7.2
Server Supported Features The GATT features a server supports, such as EATT. 1 octet 5.2 7.4
SMP 17
SMP command in B-frame An SMP command on the Security Manager channel: a code, then that command's data. 1-N octets 4.0 3.3
Pairing Request in SMP command 0x01 The initiator starts pairing, with its capabilities and the keys it wants exchanged. 7 octets 4.0 3.5.1
Pairing Response in SMP command 0x02 The responder answers with its capabilities; together they decide the pairing method. 7 octets 4.0 3.5.2
Pairing Confirm in SMP command 0x03 A commitment to a random value, checked once the value is revealed. 17 octets 4.0 3.5.3
Pairing Random in SMP command 0x04 Reveals the random value committed to in Pairing Confirm. 17 octets 4.0 3.5.4
Pairing Failed in SMP command 0x05 Ends pairing, with a reason. 2 octets 4.0 3.5.5
Encryption Information in SMP command 0x06 Hands over a long-term key (LE legacy pairing). 17 octets 4.0 3.6.2
Central Identification in SMP command · formerly Master Identification 0x07 Hands over EDIV and Rand, which identify the long-term key. Master Identification before 5.3. 11 octets 4.0 3.6.3
Identity Information in SMP command 0x08 Hands over the identity resolving key, to resolve private addresses later. 17 octets 4.0 3.6.4
Identity Address Information in SMP command 0x09 Hands over the device's public or static random identity address. 8 octets 4.0 3.6.5
Signing Information in SMP command 0x0A Hands over the key for signed writes; removed in 6.3. 17 octets 4.0–6.2 3.6.6
Security Request in SMP command 0x0B The peripheral asks the central to start pairing or encryption. 2 octets 4.0 3.6.7
Pairing Public Key in SMP command 0x0C Sends the device's P-256 public key (Secure Connections, 4.2 on). 65 octets 4.2 3.5.6
Pairing DHKey Check in SMP command 0x0D Proves both sides computed the same Diffie-Hellman key (Secure Connections). 17 octets 4.2 3.5.7
Keypress Notification in SMP command 0x0E Reports keypresses during passkey entry. 2 octets 4.2 3.5.8
AuthReq in Pairing Request The AuthReq octet: bonding flags, MITM, then Secure Connections, keypress and CT2 bits as versions add them. 1 octet 4.0 3.5.1
Key Distribution in Pairing Request The key distribution octet: which keys follow pairing. 1 octet 4.0 3.6.1
GAP 3
AD structure in ADV_IND One AD structure of advertising data: a length, a type, then the data; structures follow each other. 1-N octets 4.0 11
EIR data structure One structure of BR/EDR extended inquiry response data: the same length, type and data as an AD structure. 4.0 8
Signed data Data signed with a signing key: the data, a counter, and a MAC. 24-N octets 4.0–6.2 10.4.1
AMP 15
AMP command in B-frame An AMP Manager command (removed after 5.2 with AMP): code, identifier, length, data. 4-N octets 4.0–5.2 3.1
AMP Command Reject in AMP command 0x01 Rejects an AMP command that was not understood. 6-N octets 4.0–5.2 3.2
AMP Discover Request in AMP command 0x02 Asks which AMP controllers the peer has. 8 octets 4.0–5.2 3.3
AMP Discover Response in AMP command 0x03 Lists the peer's AMP controllers. 11-N octets 4.0–5.2 3.4
AMP Change Notify in AMP command 0x04 Reports a change of the controller list. 7-N octets 4.0–5.2 3.5
AMP Change Response in AMP command 0x05 Acknowledges a change notification. 4 octets 4.0–5.2 3.6
AMP Get Info Request in AMP command 0x06 Asks for information about one AMP controller. 5 octets 4.0–5.2 3.7
AMP Get Info Response in AMP command 0x07 Answers with the controller's bandwidth, latency and capabilities. 22 octets 4.0–5.2 3.8
AMP Get AMP Assoc Request in AMP command 0x08 Asks for the AMP association data of a controller. 5 octets 4.0–5.2 3.9
AMP Get AMP Assoc Response in AMP command 0x09 Answers with the AMP association data. 8 octets 4.0–5.2 3.10
AMP Create Physical Link Request in AMP command 0x0A Asks to create a physical link on an AMP. 8 octets 4.0–5.2 3.11
AMP Create Physical Link Response in AMP command 0x0B Answers a create physical link request. 7 octets 4.0–5.2 3.12
AMP Disconnect Physical Link Request in AMP command 0x0C Asks to disconnect a physical link on an AMP. 6 octets 4.0–5.2 3.13
AMP Disconnect Physical Link Response in AMP command 0x0D Answers a disconnect request. 7 octets 4.0–5.2 3.14
Controller list in AMP Discover Response The list of AMP controllers: each entry an ID, a type and a status. 15 octets 4.0–5.2 3.4